Component guide · Advanced · 4 min read
Raspberry Pi Microcontroller Chips

RP2040 (Single, Reel of 100 and 500), RP2350A QFN-60, RP2350B QFN-80 (Single, Reels of 100 and 500) and RP2354B with 2MB Stacked Flash
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are the bare chips used on Pico boards, for designing your own PCB. RP2040 (QFN-56) has two Cortex-M0+ cores and needs external QSPI flash. RP2350A (QFN-60, 30 GPIO) and RP2350B (QFN-80, 48 GPIO) add Cortex-M33 and RISC-V cores and security. RP2354 has 2MB flash stacked inside, so no external flash chip is needed. Reels suit production runs.
Key specs at a glance
- RP2040
- QFN-56, 2x M0+ 133 MHz, 264KB RAM, external flash
- RP2350A
- QFN-60, 30 GPIO, 520KB RAM
- RP2350B
- QFN-80, 48 GPIO
- RP2354
- RP2350 with 2MB stacked flash
- Clock
- 12 MHz crystal
- Power
- Single 3.3V supply plus internal core regulator (RP2350 uses an external inductor)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Raspberry Pi RP2040 Microcontroller IC₹64
Option 2Raspberry Pi RP2040 Microcontroller IC (Reel of 100)₹6,367
Option 3Raspberry Pi RP2040 Microcontroller IC – Reel of 500₹31,839
Option 4Raspberry Pi RP2350A Dual Core Microcontroller IC₹114
Option 5Raspberry Pi RP2350A Microcontroller IC (Reel of 500)₹48,207
Option 6Raspberry Pi RP2350A Microcontroller IC – Reel of 100₹9,687
What the Raspberry Pi RP2040, RP2350A, RP2350B and RP2354 microcontroller chips for your own PCB is
The RP2040 and RP2350 are Raspberry Pi's microcontroller chips, sold on their own for custom PCBs; the RP2350 adds faster Arm Cortex-M33 or RISC-V cores, more RAM and security.
Start from Raspberry Pi's 'Hardware design with RP2040' or the RP2350 minimal design files and copy the reference layout: QSPI flash close to the chip, 12 MHz crystal with its load capacitors, decoupling on every supply pin, and the BOOTSEL button on the flash chip-select line.
RP2350's switching core regulator needs the specified inductor and careful layout. Use the Pico 2 schematic as a guide. A chip with blank flash enumerates as a USB drive, so programming in production needs only a USB connection.
Raspberry Pi RP2040, RP2350A, RP2350B and RP2354 microcontroller chips for your own PCB pinout
The pins on the Raspberry Pi RP2040, RP2350A, RP2350B and RP2354 microcontroller chips for your own PCB and what each one does.
| Pin | Function |
|---|---|
| QSPI | External flash (not on RP2354) |
| XIN / XOUT | 12 MHz crystal |
| USB DP / DM | USB 1.1 device or host |
| RUN | Reset, active low |
| IOVDD / DVDD | 3.3V I/O and core supply |
- QSPI
- External flash (not on RP2354)
- XIN / XOUT
- 12 MHz crystal
- USB DP / DM
- USB 1.1 device or host
- RUN
- Reset, active low
- IOVDD / DVDD
- 3.3V I/O and core supply
Wiring the Raspberry Pi RP2040, RP2350A, RP2350B and RP2354 microcontroller chips for your own PCB
Use a stencil and reflow or hot air; QFN parts need the centre pad soldered to ground.
| Raspberry Pi RP2040, RP2350A, RP2350B and RP2354 microcontroller chips for your own PCB pin | Connection | Note |
|---|---|---|
| QSPI_SS | Flash CS and BOOTSEL button to GND | Button forces USB boot |
| XIN/XOUT | 12 MHz crystal | Load capacitors per datasheet |
| USB | 27Ω series resistors | Match the reference design |
- QSPI_SS
- Connection:
- Flash CS and BOOTSEL button to GND
- Note:
- Button forces USB boot
- XIN/XOUT
- Connection:
- 12 MHz crystal
- Note:
- Load capacitors per datasheet
- USB
- Connection:
- 27Ω series resistors
- Note:
- Match the reference design
Example code
A Raspberry Pi Debug Probe or a second Pico running debugprobe firmware works as the SWD adapter.
1. Check the 3.3V rail and the core voltage before fitting the chip if possible.
2. Hold BOOTSEL and plug in USB: the board should appear as a drive.
3. Copy a blink UF2 (built for your LED pin) to the drive.
4. If no drive appears, check the crystal, USB resistors and RUN pin.
5. Use picotool info to read the chip and flash size.
6. Connect SWD (SWCLK, SWDIO) to a debug probe for step debugging.Setup and tuning
add a 12 MHz crystal, external QSPI flash (W25Q series), 3.3 V regulator and decoupling capacitors, following the official hardware design guide.
the RP2040 needs 1.1 V from its internal regulator; the RP2350 uses an on-chip switching regulator with an inductor.
route D+ and D- as a 90 Ω pair with 27 Ω series resistors on the RP2040.
add a BOOTSEL button on the flash chip select so you can load UF2 files.
copy the reference layout closely for the crystal, flash and regulator.
What you need
Shop this list11 of 11 found in our store · ₹69,122
Raspberry Pi RP2040 Microcontroller IC: the part this guide coversRaspberry Pi RP2040 Microcontroller IC₹64
Raspberry Pi RP2040 Microcontroller IC (Reel of 100): another version this guide coversRaspberry Pi RP2040 Microcontroller IC₹64
Raspberry Pi RP2040 Microcontroller IC – Reel of 500: another version this guide coversRaspberry Pi RP2040 Microcontroller IC₹64
Raspberry Pi RP2350A Dual Core Microcontroller IC: another version this guide coversRaspberry Pi RP2350A Dual Core Microcontroller IC₹114
Raspberry Pi RP2350A Microcontroller IC (Reel of 500): another version this guide coversRaspberry Pi RP2350A Microcontroller IC (Reel of 500)₹48,207
Raspberry Pi RP2350A Microcontroller IC – Reel of 100: another version this guide coversRaspberry Pi RP2350A Microcontroller IC – Reel of 100₹9,687
Raspberry Pi RP2350B Microcontroller IC: another version this guide coversRaspberry Pi RP2350B Microcontroller IC₹123
Raspberry Pi RP2350B Microcontroller IC (Reel of 100): another version this guide coversRaspberry Pi RP2350B Microcontroller IC₹123
Raspberry Pi RP2350B Microcontroller IC (Reel of 500): another version this guide coversRaspberry Pi RP2350B Microcontroller IC₹123
Raspberry Pi RP2354B0A2 Microcontroller IC: another version this guide coversRaspberry Pi RP2354B0A2 Microcontroller IC₹10,469
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- Raspberry Pi Pico: the reference board.
- RP2350 boards: ready-made boards.
- RP2040 boards beyond the Pico: RP2040 boards.
Common mistakes to avoid
- Ignoring the official layout guide.
- Leaving out the BOOTSEL button.
- Poor crystal routing.
- Wrong inductor on the RP2350 regulator.
Frequently asked questions
What parts does an RP2040 need on a custom PCB?
A 12 MHz crystal, QSPI flash, a 3.3 V regulator, decoupling capacitors and USB resistors.
What is new in the RP2350?
Faster Cortex-M33 or RISC-V cores, 520 KB RAM, security features and more PIO.
How do I program a custom RP2040 board?
Hold BOOTSEL while plugging in USB, then copy a UF2 file to the drive.
Can I skip the external flash?
Not on the RP2040; some RP2350 versions have flash inside the package.
Why does my custom board not enumerate on USB?
Check the crystal, USB resistors, flash wiring and the 1.1 V core supply.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


