How-to · Beginner · 3 min read
School Tinkering Lab Safety Rules
Soldering, Tools, Batteries, Glue and 3D Printers
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Wear eye protection for cutting, drilling and soldering; solder only in a ventilated area with the iron in its holder; keep power tools supervised; charge and store batteries carefully; keep mains out of student projects; never block the exit; and know where the first-aid kit and fire extinguisher are before the first class starts.
Key specs at a glance
- Eye protection
- Goggles for cutting, drilling, soldering
- Soldering
- Ventilation, stand, no touching the tip
- Hot glue
- Hot nozzle and glue, use a tray
- Batteries
- Charge supervised, no damaged cells
- Mains
- Low voltage only for projects
- Emergency
- First aid and extinguisher by the door
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
General rules for every session
- Tie back long hair and loose clothing; closed shoes only.
- No food or drink at the benches.
- Know where the first-aid kit, extinguisher and exit are.
- Report every injury, however small.
- Tidy as you go; clear the bench at the end.
- Never work alone with tools or heat.
Soldering
- Wear goggles and work in a ventilated area; do not breathe the fumes.
- Keep the iron in its stand when not in use and switch it off when you leave.
- Never touch the tip. Treat every hot tool as hot until it has cooled.
- Use a helping hand to hold the work.
- Wash hands after soldering, especially if using leaded solder.
Hand tools, drill and heat gun
- Cut and drill away from your body and clamp the work.
- Use the right tool for the job; never force a saw or file.
- Use the drill and heat gun only with teacher supervision.
- Keep blades and bits stored when not in use.
Hot glue
- The nozzle and the glue are hot enough to burn. Rest the gun on its stand or a tray.
- Let the glue cool before you touch it.
- Don't pull hot strings of glue with bare fingers.
Batteries and power
- Use the charger supplied with a battery, and charge in a safe place with a teacher present.
- Don't use swollen, damaged or hot batteries.
- Never connect motors to a board's 5 V pin; use a separate supply.
- Keep student projects at low voltage. Wiring mains devices is for qualified adults only.
- Use fused extension boards, and don't plug one into another.
3D printers
- The nozzle and bed are hot; wait until they cool before touching them.
- Keep the printer on a stable table with ventilation.
- Never leave a long print without someone checking in.
- Use PLA first; stay away from filaments that need an enclosure unless an adult has set it up.
Lasers, sensors and gas tests
- Use only the low-power laser modules in the kit and never point them at people, animals or mirrors.
- Test gas sensors only with small safe sources such as an incense stick, never with a lighter or real gas.
- Hobby gas sensors are for learning and are not certified alarms.
About this guide
Geekobot is an independent shop. It is not endorsed by, approved by or affiliated with NITI Aayog or the Atal Innovation Mission. The package contents described here come from the public AIM equipment list for a batch of 60 students, summarised in our own words. Check the current list before you buy, because AIM updates it from time to time. Quantities are the suggested numbers for 60 students; a smaller school can scale them down. The official document also sets procurement rules for ATL schools (including purchase through the GeM portal), so check them before ordering for an ATL grant. For questions about the programme, schools should contact AIM using the address in the official document.
Common mistakes to avoid
- Soldering without goggles.
- Leaving the iron on and unattended.
- Powering a motor from the board's 5 V pin.
- Charging batteries unsupervised overnight.
- Pointing a laser module at someone's face.
Frequently asked questions
Do students need gloves?
Gloves help with hot glue and cutting jobs, but not around moving drills or rotary tools where they can get caught. Follow the teacher's instructions for each task.
Is it safe for children to solder?
With supervision, a stand, ventilation, goggles and small groups, soldering is a standard school activity. Younger children may start with breadboards only.
What should the first-aid kit contain?
A standard portable medical first-aid kit as listed in the equipment list. Check expiry dates and restock after use.
Where can I find official safety guidance?
In the guidelines published on the AIM website, and in your school's own safety policy.
Parts for this guide
Search the store for the parts named above, or ask Geeko AI which one fits your project.
Terms in this guide
Keep learning
Sources
- AIM: ATL Equipment List, Batch of 60 Students (public PDF at aim.gov.in)
- AIM: Atal Tinkering Labs overview page at aim.gov.in/atl.php
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




