How-to · Beginner · 4 min read
How to Set Up a School Tinkering Lab
Room Plan, Storage, Stations and Rules
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Divide the room into four zones: an electronics bench, a tools and making area, a 3D printing corner and a clean documentation table. Use labelled drawers for small parts, a pegboard for tools, fused power strips along the walls and clear walkways. Put safety rules and a first-aid kit by the door before the first class.
Key specs at a glance
- Zones
- Electronics, tools, printing, documentation
- Storage
- Labelled drawers and a pegboard
- Power
- Fused extension boards on the walls
- Safety
- First aid, extinguisher and goggles by the door
- Group size
- Pairs or groups of 3 to 4
- Routine
- Plan, build, test, tidy, show
Plan the four zones
These are suggestions to adapt, not rules from the official document.
| Zone | What goes there | Equipment |
|---|---|---|
| Electronics bench | Circuits, coding, testing | Uno boards, breadboards, sensors, laptops, multimeters |
| Tools and making | Cutting, drilling, soldering | Pegboard, vice, drill, soldering kits with ventilation |
| 3D printing corner | Printer on a stable table with UPS | Printer, filament boxes, tools to remove prints |
| Documentation table | Planning and showing | Notebooks, camera, whiteboard, finished-project shelf |
- Electronics bench
- What goes there:
- Circuits, coding, testing
- Equipment:
- Uno boards, breadboards, sensors, laptops, multimeters
- Tools and making
- What goes there:
- Cutting, drilling, soldering
- Equipment:
- Pegboard, vice, drill, soldering kits with ventilation
- 3D printing corner
- What goes there:
- Printer on a stable table with UPS
- Equipment:
- Printer, filament boxes, tools to remove prints
- Documentation table
- What goes there:
- Planning and showing
- Equipment:
- Notebooks, camera, whiteboard, finished-project shelf
Steps to set up
- 1Choose the room. Good light, ventilation, a lockable cupboard and enough sockets. Avoid putting the soldering area near books or curtains.
- 2Fit the walls. Hang the pegboards and fix fused extension boards at bench height.
- 3Install the safety kit. First-aid box, fire extinguisher and goggles stay by the door.
- 4Set out storage. Label each drawer with the part name and a photo. Keep resistors, LEDs and sensors in separate drawers.
- 5Arrange benches. Seat students facing the instructor on one side and keep the middle for power and demonstrations.
- 6Test the electrics. Test every socket and the extension boards. Check the UPS with the printer.
- 7Write the rules. Put the lab safety rules on the wall.
- 8Start small. Run the first lesson from the Package 1 lesson plan.
- 9Review each term. Check the stock, replace missing parts and tidy the drawers.
A weekly routine that works
gather, rules reminder, today's goal.
work in pairs, teacher moves between benches.
each group demonstrates what works.
parts back in labelled drawers, tools on the pegboard, benches wiped.
a line in the project notebook about what changed.
Share responsibility
Give students roles that rotate each week: tool keeper, parts keeper, safety monitor and documenter. It keeps the lab tidy and gives everyone a turn at leading.
About this guide
Geekobot is an independent shop. It is not endorsed by, approved by or affiliated with NITI Aayog or the Atal Innovation Mission. The package contents described here come from the public AIM equipment list for a batch of 60 students, summarised in our own words. Check the current list before you buy, because AIM updates it from time to time. Quantities are the suggested numbers for 60 students; a smaller school can scale them down. The official document also sets procurement rules for ATL schools (including purchase through the GeM portal), so check them before ordering for an ATL grant. For questions about the programme, schools should contact AIM using the address in the official document.
Set up a school tinkering lab
You need: Electronics kit, Safety equipment · Tools: Pegboard, Labelled storage drawers, Fused extension boards
Get the parts2 of 2 found in our store · ₹18,087
Electronics kitElectronics Experiments Kit₹578
Safety equipmentAtal Tinkering Lab Package 4: Power Supply, Accessories and Safety Equipment₹17,509
- 1Choose and prepare the roomPick a bright, ventilated room with enough sockets and a lockable cupboard.
- 2Fit storage and powerHang pegboards, fix fused extension boards and set out labelled drawers.
- 3Install safety equipmentPlace the first-aid kit, extinguisher and goggles by the door and put the rules on the wall.
- 4Arrange zones and testSet out electronics, tools, printing and documentation zones, then test sockets and the UPS.
- 5Run the first lessonStart with a simple Package 1 project, then review and tidy at the end of each session.
Common mistakes to avoid
- Putting the soldering bench against a wall with no ventilation.
- Mixing all small parts in one box.
- Having too few power sockets and running long extension chains.
- Starting with the 3D printer before the electronics bench works.
- No rule about tidying, so the lab ends up in chaos by week three.
Frequently asked questions
How big should the lab room be?
Large enough for groups to work at benches with clear walkways, and for the printer and tool area to be separated from the electronics bench. A standard classroom is a common starting point.
How many students can work at once?
The official equipment list is sized for a batch of 60 students only. Plan for groups of three or four at each bench.
Where should the 3D printer go?
On a stable table away from the walkway, ideally with ventilation, and connected to its own UPS.
How do we keep small parts from vanishing?
Label drawers with names and photos, make part keeping a student role, and count key items at the end of each term.
Parts for this guide
Search the store for the parts named above, or ask Geeko AI which one fits your project.
Terms in this guide
Keep learning
Sources
- AIM: ATL Equipment List, Batch of 60 Students (public PDF at aim.gov.in)
- AIM: Atal Tinkering Labs overview page at aim.gov.in/atl.php
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




