Component guide · Intermediate · 4 min read
STM32 and STM8 Core Boards

WeAct STM32G431, G473, G491 and H562, AT32F403A BlackPill, STM32F030F4P6, Maple Mini, STM32F407VET6, Olimexino-STM32, Waveshare Open405R and XNUCLEO-F103RB, Pyboard and STM8S Boards
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Core boards put an STM32 chip, crystal, regulator and USB on a small board without a built-in debugger. They cost less than Nucleo boards and fit breadboards. Program them over USB DFU, a serial bootloader or an ST-LINK on the SWD pins. The Pyboard runs MicroPython out of the box. STM8S boards are a separate 8-bit family that uses different tools.
Key specs at a glance
- WeAct G431, G473, G491
- Cortex-M4 at 170 MHz, strong analog and motor timers
- WeAct H562
- Cortex-M33 at 250 MHz
- F030F4P6
- Cortex-M0 at 48 MHz, 16 KB flash, 20 pins
- Maple Mini / F407VET6
- F103 at 72 MHz / F407 at 168 MHz
- Pyboard PYB1.1
- STM32F405, MicroPython, microSD
- STM8S103 / S105
- 8-bit STM8 at 16 MHz, programmed with ST-LINK SWIM
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1WeAct STM32G431CBT6 Mini Core Development Board₹559
Option 2WeAct STM32G473VET6 Cortex-M4 Development Board₹809
Option 3WeAct Studio STM32G491VET6 MCU Development Board₹719
Option 4WeAct Studio STM32H562VGT6 Core Board₹939
Option 5WeAct Studio AT32F403ACGU7 BlackPill Core Learning Board₹529
Option 6STM32F030F4P6 ARM Cortex-M0 Core Board₹166
What the STM32 and STM8 core boards (WeAct G4 and H5, Maple Mini, F030F4, F407VET6, Pyboard, STM8S) is
STM32 and STM8 core boards, such as the Blue Pill, Black Pill and STM8S minimal boards, are low-cost microcontroller boards for learning and embedded projects.
Most of these boards have no on-board debugger. An ST-LINK V2 on the SWD pins (3.3V, SWDIO, SWCLK, GND) is the most reliable way to flash and debug. The WeAct and F4 boards also support USB DFU: hold BOOT0, press reset and flash with STM32CubeProgrammer.
The AT32F403A is an Artery chip, similar to STM32F103 but faster, with its own Arduino core. STM8 boards need ST-LINK's SWIM pin and tools such as SDCC or STVD.
STM32 and STM8 core boards (WeAct G4 and H5, Maple Mini, F030F4, F407VET6, Pyboard, STM8S) pinout
The pins on the STM32 and STM8 core boards (WeAct G4 and H5, Maple Mini, F030F4, F407VET6, Pyboard, STM8S) and what each one does.
| Pin | Function |
|---|---|
| SWD | 3.3V, SWDIO, SWCLK, GND for ST-LINK |
| BOOT0 button | Enter the ROM bootloader |
| USB-C or micro USB | Power and DFU or USB CDC |
| Header pins | All GPIO, 3.3V logic |
| SWIM | On STM8 boards instead of SWD |
- SWD
- 3.3V, SWDIO, SWCLK, GND for ST-LINK
- BOOT0 button
- Enter the ROM bootloader
- USB-C or micro USB
- Power and DFU or USB CDC
- Header pins
- All GPIO, 3.3V logic
- SWIM
- On STM8 boards instead of SWD
Wiring the STM32 and STM8 core boards (WeAct G4 and H5, Maple Mini, F030F4, F407VET6, Pyboard, STM8S)
Do not power the board from the ST-LINK's 3.3V and USB at the same time on cheap clones. Analog pins are not 5V tolerant.
| STM32 and STM8 core boards (WeAct G4 and H5, Maple Mini, F030F4, F407VET6, Pyboard, STM8S) pin | Connection | Note |
|---|---|---|
| ST-LINK V2 | SWDIO, SWCLK, GND, 3.3V | Short wires |
| USB-UART | PA9 TX, PA10 RX | For the serial bootloader |
| Sensors | I2C on PB6/PB7 on many boards | 3.3V logic |
- ST-LINK V2
- Connection:
- SWDIO, SWCLK, GND, 3.3V
- Note:
- Short wires
- USB-UART
- Connection:
- PA9 TX, PA10 RX
- Note:
- For the serial bootloader
- Sensors
- Connection:
- I2C on PB6/PB7 on many boards
- Note:
- 3.3V logic
Example code
Pick the matching board in the STM32 core (for example 'Generic STM32G4 series') and set the upload method to STM32CubeProgrammer (SWD or DFU).
// Board: Nucleo-64 (or your board) in Tools > Board > STM32 MCU based boards
void setup() {
pinMode(LED_BUILTIN, OUTPUT);
Serial.begin(115200); // goes out over the ST-LINK virtual COM port
}
void loop() {
digitalWrite(LED_BUILTIN, !digitalRead(LED_BUILTIN));
Serial.println(millis());
delay(500);
}Setup and tuning
use an ST-Link V2 on SWD (SWDIO, SWCLK, GND, 3.3 V) for STM32, or SWIM for STM8.
use STM32CubeIDE, Arduino (STM32duino) or PlatformIO for STM32; STVD or SDCC for STM8.
set BOOT0 low for normal run.
Black Pill boards support USB DFU; Blue Pills may need a 1.5 kΩ D+ resistor fix.
pins are 3.3 V; some are 5 V tolerant (FT), but check the datasheet.
What you need
Shop this list18 of 18 found in our store · ₹22,604
WeAct STM32G431CBT6 Mini Core Development Board: the part this guide coversWeAct STM32G431CBT6 Mini Core Development Board₹559
WeAct STM32G473VET6 Cortex-M4 Development Board: another version this guide coversWeAct STM32G473VET6 Cortex-M4 Development Board₹809
WeAct Studio STM32G491VET6 MCU Development Board: another version this guide coversWeAct Studio STM32G491VET6 MCU Development Board₹719
WeAct Studio STM32H562VGT6 Core Board: another version this guide coversWeAct Studio STM32H562VGT6 Core Board₹939
WeAct Studio AT32F403ACGU7 BlackPill Core Learning Board: another version this guide coversWeAct Studio AT32F403ACGU7 BlackPill Core Learning Board₹529
STM32F030F4P6 ARM Cortex-M0 Core Board: another version this guide coversSTM32F030F4P6 ARM Cortex-M0 Core Board₹166
STM32F030F4P6 ARM Cortex-M0 MCU (48 MHz) STMicroelectronics: another version this guide coversSTM32F030F4P6 ARM Cortex-M0 MCU (48 MHz) STMicroelectronics₹59
STM32F103CBT6 Maple Mini Development Board: another version this guide coversSTM32F103CBT6 Maple Mini Development Board₹591
STM32F407VET6 ARM Cortex-M4 DSP/FPU Development Board: another version this guide coversSTM32F407VET6 ARM Cortex-M4 DSP/FPU Development Board₹1,939
Olimex OLIMEXINO-STM32 Board with STM32F103RBT6 Microcontroller: another version this guide coversOlimex OLIMEXINO-STM32 Board with STM32F103RBT6 Microcontroller₹2,499
Waveshare Open405R-C Package A, STM32F4 Dev Board: another version this guide coversWaveshare Open405R-C Package A, STM32F4 Dev Board₹8,089
Waveshare XNUCLEO-F103RB STM32 NUCLEO Development Board: another version this guide coversWaveshare XNUCLEO-F103RB STM32 NUCLEO Development Board₹4,079
PYboard PYB1.1 STM32F405 ARM Cortex-M4 Board: another version this guide coversPYboard PYB1.1 STM32F405 ARM Cortex-M4 Board₹979
STM8S103F3P6 STM8 Minimum System Development Board: another version this guide coversSTM8S103F3P6 STM8 Minimum System Development Board₹98
STM8S105K4T6 ARM Core Development Board: another version this guide coversSTM8S105K4T6 ARM Core Development Board₹369
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
USB cable: for power, flashing and the virtual COM portUSB Cable₹28
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Alternatives and when to choose them
- STM32 Blue Pill and Black Pill: the classic cheap boards.
- WeAct MCU core boards: other WeAct chips.
- STM32 Nucleo boards: built-in debugger.
Common mistakes to avoid
- BOOT0 left high.
- Assuming all pins are 5 V tolerant.
- Fake chips on cheap boards.
- Wrong ST-Link wiring.
Frequently asked questions
How do I program a Blue Pill?
Use an ST-Link V2 over SWD with STM32CubeIDE or Arduino.
Why does my Blue Pill not show on USB?
Some have the wrong USB pull-up resistor or no USB bootloader.
Which is better, Blue Pill or Black Pill?
Black Pill uses the faster STM32F401/F411 with better USB.
Are STM32 pins 5 V tolerant?
Some pins marked FT are; analog pins are not.
How do I program an STM8 board?
Use an ST-Link V2 connected to the SWIM, reset, 3.3 V and GND pins.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

