Component guide · Intermediate · 5 min read
STM32 X-NUCLEO Expansion Boards

ToF (53L0A1, 53L3, 53L5A1, 6180A1), Sensors (IKS02A1), BLE (BNRG2A1, IDB05A2), Sub-GHz (IDS01A4/A5, S2-LP), GNSS, Audio, Display, EEPROM, STSAFE, Power Measurement and Industrial I/O
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
X-NUCLEO boards are ST's plug-in expansion boards for Nucleo development boards. Each one adds a single ST chip, such as a VL53 time-of-flight sensor, a BlueNRG Bluetooth radio, a Teseo GNSS receiver or an industrial output driver, on Arduino Uno headers. ST gives a matching X-CUBE software pack for STM32CubeIDE, and many also have STM32duino libraries.
Key specs at a glance
- Connector
- Arduino Uno R3 headers, some also ST morpho
- Logic
- 3.3V
- Software
- X-CUBE packs for STM32Cube, STM32duino libraries for many
- Host
- Any Nucleo-64; many work on Nucleo-144 too
- Satellite boards
- ToF boards include small break-out boards for remote mounting
- Industrial boards
- Need their own 24V supply
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ST X-NUCLEO-53L0A1 VL53L0X Ranging/Gesture Expansion Board₹3,959
Option 2ST X-NUCLEO-53L5A1 VL53L5CX ToF Expansion for Nucleo₹3,959
Option 3STM32 Nucleo VL53L3CX Time-of-Flight Expansion Board₹3,779
Option 4STMicroelectronics X-NUCLEO-6180A1 ToF Expansion Board₹3,179
Option 5STMicroelectronics X-NUCLEO-IKS02A1 Nucleo Sensor Board₹2,759
Option 6STMicroelectronics X-NUCLEO-BNRG2A1 STM32 Nucleo BLE 5.0 Expansion₹4,589
What the STM32 X-NUCLEO expansion boards (sensors, ToF, BLE, sub-GHz, GNSS, audio, industrial I/O) is
STM32 X-NUCLEO expansion boards add sensors, motor drivers, wireless, power and industrial I/O to Nucleo boards through Arduino Uno-style or Morpho headers.
Pick the board by the ST chip it carries:
53L0A1 (VL53L0X), 53L3A2 style VL53L3CX, 53L5A1 (VL53L5CX 8x8 zones), 6180A1 (VL6180X).
IKS02A1 (ISM330DHCX IMU, IIS2MDC magnetometer, IIS2DLPC, STTS22H, IMP34DT05 microphone).
BNRG2A1 and IDB05A2 (BlueNRG BLE), IDS01A4/A5 and S2-LP boards (868 or 915 MHz), SPIRIT1 169 MHz daughter board.
GNSS1A1 (Teseo-LIV3F), CCA01M1 (STA350BW audio amplifier), AMICAM1 (microphones), GFX01M2 (SPI display), EEPRMA2 (EEPROM), STSAFE-A110 (secure element), LPM01A (power meter for low-power code), IPS160HF, IPS161HF and ISO8200AQ (industrial outputs), L6362A and L6360 (IO-Link), MB1683 camera adapter.
STM32 X-NUCLEO expansion boards (sensors, ToF, BLE, sub-GHz, GNSS, audio, industrial I/O) pinout
The pins on the STM32 X-NUCLEO expansion boards (sensors, ToF, BLE, sub-GHz, GNSS, audio, industrial I/O) and what each one does.
| Pin | Function |
|---|---|
| Arduino Uno R3 headers | Plug-in for X-NUCLEO boards and many 3.3V Arduino shields |
| ST morpho headers | Two long rows with every pin of the STM32 |
| ST-LINK USB | Drag-and-drop flashing, debugging and virtual COM port |
| Solder bridges | Select which STM32 pins reach the headers |
| Power jumper | USB, external 5V or VIN |
- Arduino Uno R3 headers
- Plug-in for X-NUCLEO boards and many 3.3V Arduino shields
- ST morpho headers
- Two long rows with every pin of the STM32
- ST-LINK USB
- Drag-and-drop flashing, debugging and virtual COM port
- Solder bridges
- Select which STM32 pins reach the headers
- Power jumper
- USB, external 5V or VIN
Wiring the STM32 X-NUCLEO expansion boards (sensors, ToF, BLE, sub-GHz, GNSS, audio, industrial I/O)
STM32 pins are 3.3V. Many are 5V tolerant (FT) but analog pins are not. Check each expansion board's solder bridges before stacking two boards.
| STM32 X-NUCLEO expansion boards (sensors, ToF, BLE, sub-GHz, GNSS, audio, industrial I/O) pin | Connection | Note |
|---|---|---|
| X-NUCLEO board | Stack on the Uno headers | Check pin conflicts in its user manual |
| USB | ST-LINK port to PC | Board appears as a USB drive |
| External power | VIN or E5V with the jumper moved | For motor boards use their own supply |
- X-NUCLEO board
- Connection:
- Stack on the Uno headers
- Note:
- Check pin conflicts in its user manual
- USB
- Connection:
- ST-LINK port to PC
- Note:
- Board appears as a USB drive
- External power
- Connection:
- VIN or E5V with the jumper moved
- Note:
- For motor boards use their own supply
Example code
Library names change between versions; open the examples that come with the STM32duino library for your exact board. For STM32CubeIDE, install the matching X-CUBE pack.
#include <Wire.h>
#include <vl53l0x_x_nucleo_53l0a1_class.h> // STM32duino X-NUCLEO-53L0A1 library
STMPE1600DigiOut xshutdown_top(&Wire, GPIO_15, (0x42 * 2));
VL53L0X_X_NUCLEO_53L0A1 sensor(&Wire, &xshutdown_top);
void setup() {
Serial.begin(115200);
Wire.begin();
sensor.begin();
sensor.InitSensor(0x10);
}
void loop() {
uint32_t mm;
if (sensor.GetDistance(&mm) == VL53L0X_ERROR_NONE) Serial.println(mm);
delay(100);
}Setup and tuning
plug onto a Nucleo-64 or Nucleo-144 board, checking header alignment.
use the matching X-CUBE expansion package with STM32CubeIDE.
check pin and I2C address conflicts before stacking boards.
set solder bridges or jumpers per the user manual.
some boards need their own supply for motors or radios.
What you need
Shop this list20 of 20 found in our store · ₹77,360
ST X-NUCLEO-53L0A1 VL53L0X Ranging/Gesture Expansion Board: the part this guide coversST X-NUCLEO-53L0A1 VL53L0X Ranging/Gesture Expansion Board₹3,959
ST X-NUCLEO-53L5A1 VL53L5CX ToF Expansion for Nucleo: another version this guide coversST X-NUCLEO-53L5A1 VL53L5CX ToF Expansion for Nucleo₹3,959
STM32 Nucleo VL53L3CX Time-of-Flight Expansion Board: another version this guide coversSTM32 Nucleo VL53L3CX Time-of-Flight Expansion Board₹3,779
STMicroelectronics X-NUCLEO-6180A1 ToF Expansion Board: another version this guide coversSTMicroelectronics X-NUCLEO-6180A1 ToF Expansion Board₹3,179
STMicroelectronics X-NUCLEO-IKS02A1 Nucleo Sensor Board: another version this guide coversSTMicroelectronics X-NUCLEO-IKS02A1 Nucleo Sensor Board₹2,759
STMicroelectronics X-NUCLEO-BNRG2A1 STM32 Nucleo BLE 5.0 Expansion: another version this guide coversSTMicroelectronics X-NUCLEO-BNRG2A1 STM32 Nucleo BLE 5.0 Expansion₹4,589
STMicroelectronics X-NUCLEO-IDB05A2 BLE Expansion Board: another version this guide coversSTMicroelectronics X-NUCLEO-IDB05A2 BLE Expansion Board₹1,879
ST BlueNRG-MS Bluetooth 4.1 LE Daughter Board STEVAL-IDB005V1D: another version this guide coversST BlueNRG-MS Bluetooth 4.1 LE Daughter Board STEVAL-IDB005V1D₹6,069
ST X-NUCLEO-IDS01A4 868MHz RF Transceiver for STM32 Nucleo: another version this guide coversST X-NUCLEO-IDS01A4 868MHz RF Transceiver for STM32 Nucleo₹1,659
STMicroelectronics X-NUCLEO-IDS01A5 SPIRIT1 RF Module 915 MHz: another version this guide coversSTMicroelectronics X-NUCLEO-IDS01A5 SPIRIT1 RF Module 915 MHz₹1,519
STM32 Nucleo S2-LP Sub-1 GHz 915MHz RF Expansion Board: another version this guide coversSTM32 Nucleo S2-LP Sub-1 GHz 915MHz RF Expansion Board₹4,419
STMicroelectronics SPIRIT1 169MHz Transceiver Daughter Board: another version this guide coversSTMicroelectronics SPIRIT1 169MHz Transceiver Daughter Board₹8,309
STMicroelectronics X-NUCLEO-GNSS1A1 Teseo-LIV3F GNSS Board: another version this guide coversSTMicroelectronics X-NUCLEO-GNSS1A1 Teseo-LIV3F GNSS Board₹3,769
STM X-NUCLEO-CCA01M1 2.1-Ch Audio Expansion w/ STA350BW: another version this guide coversSTM X-NUCLEO-CCA01M1 2.1-Ch Audio Expansion w/ STA350BW₹3,779
STMicroelectronics X-NUCLEO-AMICAM1 STM32 Nucleo Audio Expansion: another version this guide coversSTMicroelectronics X-NUCLEO-AMICAM1 STM32 Nucleo Audio Expansion₹3,779
STM32 X-NUCLEO-GFX01M2 SPI Display Expansion Board: another version this guide coversSTM32 X-NUCLEO-GFX01M2 SPI Display Expansion Board₹3,909
STMicroelectronics X-NUCLEO-EEPRMA2 EEPROM Expansion: another version this guide coversSTMicroelectronics X-NUCLEO-EEPRMA2 EEPROM Expansion₹1,789
STSAFE-A110 Secure Element Expansion Board for STM32 Nucleo: another version this guide coversSTSAFE-A110 Secure Element Expansion Board for STM32 Nucleo₹1,849
STMicroelectronics X-NUCLEO-LPM01A Power Measurement Board: another version this guide coversSTMicroelectronics X-NUCLEO-LPM01A Power Measurement Board₹8,619
STM32 Nucleo IPS161HF Industrial Digital Output Board: another version this guide coversSTM32 Nucleo IPS161HF Industrial Digital Output Board₹3,789
Alternatives and when to choose them
- STM32 Nucleo boards: the host boards.
- VL53L5CX multizone ToF: the same sensor on a breakout.
- STM32 motor control boards: STSPIN boards.
Common mistakes to avoid
- Pin conflicts when stacking.
- Wrong jumpers.
- Using 5 V Arduino boards blindly.
- Missing external power.
Frequently asked questions
Which software goes with an X-NUCLEO board?
Use the matching X-CUBE software package listed for that board.
Can I stack several X-NUCLEO boards?
Yes, if pins and I2C addresses do not clash.
Can I use them with Arduino boards?
Some work with Arduino Uno because of the same headers, but check voltages.
Why does my sensor board not respond?
The jumper or solder bridge settings do not match your setup.
Do they need extra power?
Motor driver and power boards usually need their own supply.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.







