Component guide · Intermediate · 4 min read
Strain Gauges and Amplifier Boards

BF350 and BX350 Gauges, BF350-3AA and Y3 Bending Sensor Amplifiers, 50kg Half-Bridge Body Scale Cell, HX711 Test Board with Display, M5Stack Mini Scales and SparkFun OpenScale
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A strain gauge is a thin foil resistor (350 ohm on BF350) glued onto metal; its resistance changes slightly as the metal stretches. BF350-3AA and Y3 boards add an amplifier for an analog output. 50kg half-bridge cells are the corner sensors from bathroom scales: use four with a combiner. HX711 test boards, M5Stack Mini Scales and SparkFun OpenScale are ready readers.
Key specs at a glance
- BF350 gauge
- 350 ohm, gauge factor about 2.0
- BF350-3AA / Y3
- Gauge plus amplifier board, analog out, 3.3-5V
- Half bridge cell
- 50kg each, 3 wires, use 4 for a 200kg scale
- HX711 test board
- HX711 plus display for bench checks
- M5Stack Mini Scales
- 5kg cell, I2C via STM32, Grove
- OpenScale
- HX711, ATmega328, serial logging, temperature
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1BF350 High Precision Resistance Strain Gauge / Pressure Sensor / Weighing Sensor 350 Ohm₹22
Option 2BF350-3AA Strain Gauge Bending Sensor Module with Amplifier₹339
Option 3BX350-3AA High Precision Resistance Strain Gauge / Full Bridge – Pressure & Weight Sensor₹62
Option 4Y3 Strain Gauge Bending Sensor Weighing Amplifier Module Version B₹327
Option 550kg Half-Bridge Load Cell Sensor for Body Scales – Alloy Steel, 30cm Cable₹42
Option 6HX711 Pressure Sensor Test Board High-Precision Module – 24-bit ADC w/ Display₹219
What the BF350 strain gauges, half-bridge scale cells and HX711 amplifier boards is
Strain gauges and load cell amplifier boards, such as the HX711, NAU7802 and INA125 boards, turn the tiny bridge signal of a load cell or strain gauge into a reading a microcontroller can use.
Glue a BF350 gauge with cyanoacrylate onto a clean, sanded metal beam along the stretch direction, then wire it in a quarter or half bridge with matching 350 ohm resistors. The amplifier boards save that work for bending demos.
For a body scale, put one half-bridge cell under each corner and wire the four into a full bridge (or use a load cell combiner board) before the HX711. M5Stack Mini Scales and OpenScale are the quickest way to a working scale with no bridge wiring.
BF350 strain gauges, half-bridge scale cells and HX711 amplifier boards pinout
The pins on the BF350 strain gauges, half-bridge scale cells and HX711 amplifier boards and what each one does.
| Pin | Function |
|---|---|
| Half bridge | Red centre tap, black and white ends (colours vary) |
| BF350-3AA | VCC, GND, AO |
| HX711 board | E+, E-, A+, A-, DT, SCK |
| M5 Mini Scales | Grove I2C |
| OpenScale | USB serial, load cell terminal |
- Half bridge
- Red centre tap, black and white ends (colours vary)
- BF350-3AA
- VCC, GND, AO
- HX711 board
- E+, E-, A+, A-, DT, SCK
- M5 Mini Scales
- Grove I2C
- OpenScale
- USB serial, load cell terminal
Wiring the BF350 strain gauges, half-bridge scale cells and HX711 amplifier boards
For a bare gauge, measure resistance before and after gluing; a cracked gauge reads open.
| BF350 strain gauges, half-bridge scale cells and HX711 amplifier boards pin | Connection | Note |
|---|---|---|
| 4 half bridges | Combiner board | Corners to one full bridge |
| Combiner E+/E-/A+/A- | HX711 | Same as a full cell |
| BF350-3AA AO | A0 | Analog read |
| M5 Mini Scales | Grove I2C | Address 0x26 |
- 4 half bridges
- Connection:
- Combiner board
- Note:
- Corners to one full bridge
- Combiner E+/E-/A+/A-
- Connection:
- HX711
- Note:
- Same as a full cell
- BF350-3AA AO
- Connection:
- A0
- Note:
- Analog read
- M5 Mini Scales
- Connection:
- Grove I2C
- Note:
- Address 0x26
Example code
This HX711 code works for the four-cell body scale once the bridge is combined. BF350-3AA and Y3 boards are read with analogRead.
#include "HX711.h"
const int DT_PIN = 3;
const int CLK_PIN = 2;
HX711 scale;
float factor = 420.0; // change until a known weight reads right
void setup() {
Serial.begin(9600);
scale.begin(DT_PIN, CLK_PIN);
scale.set_scale(factor);
scale.tare(); // empty platform = 0
Serial.println("Place a known weight");
}
void loop() {
Serial.print("Weight: ");
Serial.print(scale.get_units(10), 1); // average of 10 readings
Serial.println(" g");
delay(500);
}Setup and tuning
connect E+, E-, A+ and A- from the load cell to the amplifier, and data pins to the microcontroller.
use the HX711 library; set gain 128 on channel A.
bond gauges with the right adhesive and wire them in a quarter, half or full bridge.
zero with no load, then set the scale with a known weight.
keep wires short, twisted and away from motors.
What you need
Shop this list11 of 12 found in our store · ₹6,468
BF350 High Precision Resistance Strain Gauge / Pressure Sensor / Weighing Sensor 350 Ohm: the part this guide coversBF350 High Precision Resistance Strain Gauge / Pressure Sensor / Weighing Sensor 350 Ohm₹22
Generic BF350-3AA Strain Gauge Bending Sensor Module with Amplifier: another version this guide coversBF350-3AA Strain Gauge Bending Sensor Module with Amplifier₹339
Generic BX350-3AA High Precision Resistance Strain Gauge / Full Bridge – Pressure & Weight Sensor: another version this guide coversBX350-3AA High Precision Resistance Strain Gauge / Full Bridge – Pressure & Weight Sensor₹62
Generic Y3 Strain Gauge Bending Sensor Weighing Amplifier Module Version B: another version this guide coversY3 Strain Gauge Bending Sensor Weighing Amplifier Module Version B₹327
Generic 50kg Half-Bridge Load Cell Sensor for Body Scales – Alloy Steel, 30cm Cable: another version this guide covers50kg Half-Bridge Load Cell Sensor for Body Scales – Alloy Steel, 30cm Cable₹42
Generic HX711 Pressure Sensor Test Board High-Precision Module – 24-bit ADC w/ Display: another version this guide coversHX711 Pressure Sensor Test Board High-Precision Module – 24-bit ADC w/ Display₹219
M5Stack Mini Scales Unit (HX711) – 5kg Load Cell, I2C Interface, STM32 MCU: another version this guide coversM5Stack Mini Scales Unit (HX711) – 5kg Load Cell, I2C Interface, STM32 MCU₹979
SparkFun OpenScale SEN-13261 Load Cell Amplifier & Data Logger Module: another version this guide coversSparkFun OpenScale SEN-13261 Load Cell Amplifier & Data Logger Module₹3,643
HX711 24-bit load cell amplifier module: to read the load cell's millivolt signalM5Stack Weight I2C Unit (HX711) – 24-Bit Precision Load Cell Amplifier Module₹609Closest match, check the specs- Uno R3 development board: the controller used in the wiring tableFind this part
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- Bar load cells: ready full-bridge cells.
- Load cell types: how bridges work.
- HX711 load cell guide: amplifier setup.
Common mistakes to avoid
- No calibration.
- Long unshielded wires.
- Poor gauge bonding.
- Swapping excitation and signal.
Frequently asked questions
How do I wire an HX711 to Arduino?
Connect DT and SCK to two digital pins, plus VCC and GND.
Why does my scale drift?
Temperature changes, creep under constant load, or poor mounting.
Which is better, HX711 or NAU7802?
NAU7802 uses I2C and has lower noise; HX711 is cheaper and simpler.
Can I bond my own strain gauges?
Yes, with careful surface preparation and the right strain gauge adhesive.
Why is the reading negative?
Swap A+ and A- or flip the load cell.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


