Component guide · Intermediate · 3 min read
Thermal Imaging Modules

MLX90640, AMG8833, MLX90614 and Thermopile Sensors
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Thermal modules measure heat without touching. Array sensors such as the AMG8833 (8x8) and MLX90640 (32x24) give a low-resolution thermal picture over I2C. Single-point sensors such as the MLX90614 and MLX90632 give one temperature for the area they see. Match the field of view to the distance, set emissivity and expect lower accuracy than a lab thermometer.
Key specs at a glance
- Arrays
- AMG8833 8x8, MLX90640 32x24
- Single point
- MLX90614, MLX90632, Asair AIT1000, thermopile elements
- Interface
- I2C (and PWM on some)
- Field of view
- Choose narrow (about 10 to 35°) or wide (about 55 to 110°)
- Supply
- 3.3 V or 5 V depending on board
- Accuracy
- About ±1 to 3 °C typical
Array or single point
Pick by whether you need a picture.
| Sensor | Output | Best for |
|---|---|---|
| AMG8833 | 8x8 pixel array | People detection, presence, simple thermal maps |
| MLX90640 | 32x24 pixel array | Better resolution thermal camera projects |
| MLX90614 | One object temperature | Non-contact thermometers |
| MLX90632 | Small digital FIR sensor | Skin and surface temperature |
| Thermopile TO-46 (ZTP-135) | Raw analog signal | Custom circuits and OEM designs |
| Asair AIT1000 module | I2C or PWM temperature | Easy industrial IR sensing |
- AMG8833
- Output:
- 8x8 pixel array
- Best for:
- People detection, presence, simple thermal maps
- MLX90640
- Output:
- 32x24 pixel array
- Best for:
- Better resolution thermal camera projects
- MLX90614
- Output:
- One object temperature
- Best for:
- Non-contact thermometers
- MLX90632
- Output:
- Small digital FIR sensor
- Best for:
- Skin and surface temperature
- Thermopile TO-46 (ZTP-135)
- Output:
- Raw analog signal
- Best for:
- Custom circuits and OEM designs
- Asair AIT1000 module
- Output:
- I2C or PWM temperature
- Best for:
- Easy industrial IR sensing
Wiring and reading
Connect 3.3 V, GND, SDA and SCL (see I2C). Use the vendor library to read the frame or temperature. Arrays need enough RAM for the pixels and a fast I2C bus; an ESP32 or Raspberry Pi is more comfortable than an UNO. Display the pixels with an interpolated colour map on a TFT screen.
Field of view and emissivity
A sensor measures the average temperature inside its cone of view, so the target must fill it. At two metres a wide-angle sensor sees a large area and averages everything in it. Set emissivity for the surface: shiny metal reads cold. Avoid reflections, direct sunlight and sudden air currents. See thermal cameras for full cameras.
Project ideas
Contactless thermometers, people counting and occupancy, hot-spot detection on electronics, thermal door sensors and cooking monitors. For other temperature sensors see choose a temperature sensor.
Try it: Temperature converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Expecting a camera-like picture from an 8x8 array.
- Measuring shiny metal without correction.
- Using a wide-angle sensor on a small target far away.
- Running I2C at a speed the sensor cannot handle.
- Pointing the sensor at the sun.
Frequently asked questions
What is a thermopile?
A heat-sensing element that makes a small voltage from infrared radiation.
MLX90640 or AMG8833?
MLX90640 has far more pixels; AMG8833 is simpler and cheaper.
Is the MLX90614 accurate for body temperature?
Only with the right sensor variant and calibration; it is not a medical device.
Can I see through glass?
No. Glass blocks infrared.
Which interface do they use?
Mostly I2C.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 33 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.





