Component guide · Beginner · 3 min read
TIP120 Darlington Transistor

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The TIP120 is an NPN Darlington power transistor in a TO-220 package. A small base current from an Arduino pin, through a 1 kΩ resistor, lets it switch up to about 5 A at 60 V, which is enough for small DC motors, solenoids and LED strips. It drops about 1 to 2 V when on, so it gets warm; a logic-level MOSFET such as the IRLZ44N wastes less power.
Key specs at a glance
- Type
- NPN Darlington (TO-220)
- Ratings
- 60 V, 5 A continuous (8 A peak), 65 W with heatsink
- Gain (hFE)
- About 1000
- Saturation drop
- About 2 V at 3 A, under 1 V at small currents
- Pinout
- Base, Collector, Emitter (left to right, text facing you)
- Built-in
- Flyback diode from emitter to collector
What the TIP120 is
A Darlington is two transistors in one package, so the gain multiplies: a few milliamps from a pin can switch amps. It works from both 5 V and 3.3 V boards, which is its advantage over MOSFETs that need a higher gate voltage.
The price is the voltage drop. At 2 A it drops about 1.5 V and turns about 3 W into heat, so it needs a heatsink at higher currents.
TIP120 pinout
The pins on the TIP120 and what each one does.
| Pin | Function |
|---|---|
| B (Base) | Control: from the pin through a 1 kΩ resistor |
| C (Collector) | To the load's negative side (also the metal tab) |
| E (Emitter) | To ground |
- B (Base)
- Control: from the pin through a 1 kΩ resistor
- C (Collector)
- To the load's negative side (also the metal tab)
- E (Emitter)
- To ground
Wiring the TIP120
The TIP120 has an internal diode, but an external flyback diode right at the motor or solenoid is still good practice. Join the motor supply ground to the controller ground.
| TIP120 pin | Arduino Uno | ESP32 |
|---|---|---|
| Base | D9 through 1 kΩ | GPIO 25 through 1 kΩ |
| Collector | Motor - | Motor - |
| Emitter | GND (shared with supply -) | GND |
| Motor + | Motor supply + (6 to 12 V) | Motor supply + |
| Flyback diode | Across the motor, stripe to + | Across the motor, stripe to + |
- Base
- Arduino Uno:
- D9 through 1 kΩ
- ESP32:
- GPIO 25 through 1 kΩ
- Collector
- Arduino Uno:
- Motor -
- ESP32:
- Motor -
- Emitter
- Arduino Uno:
- GND (shared with supply -)
- ESP32:
- GND
- Motor +
- Arduino Uno:
- Motor supply + (6 to 12 V)
- ESP32:
- Motor supply +
- Flyback diode
- Arduino Uno:
- Across the motor, stripe to +
- ESP32:
- Across the motor, stripe to +
Example code
This only drives the motor one way. To reverse it use an H-bridge such as the L298N.
const int BASE = 9;
void setup() { pinMode(BASE, OUTPUT); }
void loop() {
analogWrite(BASE, 255); delay(2000); // full speed
analogWrite(BASE, 128); delay(2000); // about half
analogWrite(BASE, 0); delay(2000); // off
}Setup and tuning
1 kΩ suits most loads; lower it (470 ohm) only for currents above about 3 A.
above about 1 A continuous, fit one; the tab is the collector, so isolate it from a metal case.
add one across motors, solenoids and relay coils.
expect the load to see 1 to 2 V less than the supply.
What you need
Shop this list6 of 7 found in our store · ₹438
TIP120 NPN Darlington Power Transistor: the part this guide coversTIP120 NPN Darlington Power Transistor₹14- Uno R3 development board: the controller used in the wiring tableFind this part
Resistor assortment kit: 1 kΩ base resistorResistor Assortment Kit₹250
1N4007 diodes: flyback diode for the motor1N4007 Rectifier Diode (Pack of 10)₹15Closest match, check the specs
IRLZ44N logic-level MOSFET: a cooler alternative for bigger loadsIRLZ44N Logic-Level N-Channel MOSFET₹42Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- IRLZ44N MOSFET: almost no voltage drop, runs cooler, needs 5 V gate drive.
- ULN2003 Darlington array: seven small Darlington switches in one chip for relays and steppers.
- Transistors and MOSFETs: how to choose a switch.
Try it: Ohms law calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Connecting the base straight to a pin without a resistor.
- Running 3 A without a heatsink.
- Putting the load on the emitter side.
- Not joining the motor supply ground to the Arduino ground.
Frequently asked questions
What is the TIP120 pinout?
Base, Collector, Emitter from left to right with the text facing you; the tab is the collector.
What base resistor should I use?
1 kΩ from a 5 V or 3.3 V pin suits most loads up to about 3 A.
TIP120 or MOSFET?
A logic-level MOSFET such as the IRLZ44N wastes far less power; the TIP120 is simpler with 3.3 V boards.
Why does it get hot?
It drops 1 to 2 V when on, so current times that drop becomes heat.
Can it switch AC?
No, it is for DC only. Use a relay or a triac for AC.
Parts for this guide
Calculators
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


