Component guide · Beginner · 3 min read
IRLZ44N Logic-Level MOSFET

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The IRLZ44N is an N-channel logic-level MOSFET in a TO-220 package. Its gate turns fully on from a 5 V Arduino pin, so it can switch LED strips, motors, solenoids and heaters far beyond what a pin can drive. Wire it on the low side: load between the positive supply and the drain, source to ground, and a gate resistor plus a 10 kΩ pull-down.
Key specs at a glance
- Type
- N-channel, logic level (TO-220)
- Ratings
- 55 V, 47 A (limited by heat in practice)
- On resistance
- About 0.022 ohm at 5 V gate, 0.025 ohm at 4 V
- Gate threshold
- 1 to 2 V
- Pinout
- Gate, Drain, Source (left to right, text facing you)
- Gate charge
- About 48 nC
What the IRLZ44N is
A MOSFET is a voltage-controlled switch. The "L" in IRLZ44N means logic level: it turns on well at 4 to 5 V, unlike the IRFZ44N which needs about 10 V.
At 3.3 V (ESP32) it conducts but not fully, so keep the current lower or add a gate driver. Without a heatsink it handles a few amps comfortably; with one, much more.
IRLZ44N pinout
The pins on the IRLZ44N and what each one does.
| Pin | Function |
|---|---|
| G (Gate) | Control: from the controller pin through a 100 to 220 ohm resistor |
| D (Drain) | To the load's negative side (also the metal tab) |
| S (Source) | To ground |
- G (Gate)
- Control: from the controller pin through a 100 to 220 ohm resistor
- D (Drain)
- To the load's negative side (also the metal tab)
- S (Source)
- To ground
Wiring the IRLZ44N
For motors, solenoids and relays add a flyback diode (such as 1N4007 or a Schottky) across the load, stripe to the positive side. Join the load supply's ground to the controller ground.
| IRLZ44N pin | Arduino Uno | ESP32 |
|---|---|---|
| Gate | D9 through 220 ohm | GPIO 25 through 100 ohm (works, not fully on) |
| Gate to Source | 10 kΩ pull-down | 10 kΩ pull-down |
| Drain | Load - (e.g. LED strip -) | Load - |
| Source | GND (shared with supply -) | GND |
| Load + | 12 V supply + | 12 V supply + |
- Gate
- Arduino Uno:
- D9 through 220 ohm
- ESP32:
- GPIO 25 through 100 ohm (works, not fully on)
- Gate to Source
- Arduino Uno:
- 10 kΩ pull-down
- ESP32:
- 10 kΩ pull-down
- Drain
- Arduino Uno:
- Load - (e.g. LED strip -)
- ESP32:
- Load -
- Source
- Arduino Uno:
- GND (shared with supply -)
- ESP32:
- GND
- Load +
- Arduino Uno:
- 12 V supply +
- ESP32:
- 12 V supply +
Example code
The same code runs a DC motor's speed. For a motor that must reverse, use an H-bridge such as the L298N instead.
const int GATE = 9;
void setup() { pinMode(GATE, OUTPUT); }
void loop() {
for (int b = 0; b <= 255; b++) { analogWrite(GATE, b); delay(8); }
for (int b = 255; b >= 0; b--) { analogWrite(GATE, b); delay(8); }
}Setup and tuning
feel the tab after a minute; if it is too hot to touch, add a heatsink or reduce the load.
isolate it with a pad and bushing if it touches a metal case.
essential for motors, solenoids and relay coils.
it works for lighter loads; for full current use a gate driver or a lower-threshold MOSFET.
What you need
Shop this list6 of 7 found in our store · ₹813
IRLZ44N Logic-Level N-Channel MOSFET: the part this guide coversIRLZ44N Logic-Level N-Channel MOSFET₹42- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Resistor assortment kit: 220 ohm gate and 10 kΩ pull-down resistorsResistor Assortment Kit₹250
1N4007 diodes: flyback diode for motors and solenoids1N4007 Rectifier Diode (Pack of 10)₹15Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- TIP120 Darlington: older bipolar switch, drops about 1 V and runs hotter.
- Transistors and MOSFETs: how BJTs and MOSFETs differ.
- MOSFET gate drivers: for fast PWM and 3.3 V control of high currents.
Try it: Ohms law calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Buying the IRFZ44N by mistake, which does not turn on fully from 5 V.
- Putting the MOSFET on the high side (between supply and load).
- No pull-down, so the load flickers on at power-up.
- No flyback diode on a motor or solenoid.
Frequently asked questions
Does the IRLZ44N work with Arduino?
Yes, a 5 V pin turns it fully on.
Can I use it with ESP32 at 3.3 V?
It turns on partly. It is fine for a few amps; for more, use a gate driver or a MOSFET rated for 2.5 V gate drive.
How much current can it switch?
A few amps without a heatsink; the 47 A rating needs serious cooling.
What is the pinout?
Gate, Drain, Source from left to right with the printed side facing you.
Why add a 10 kΩ resistor?
It holds the gate low so the load stays off while the controller is starting.
Parts for this guide
Calculators
Projects that use it
Put this into practice: 8 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


