Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsTape the DS18B20 probe to the laptop stand where the exhaust sits. Above 40 °C the MOSFET switches the fan on at full speed; it stays on until the probe drops back under 36 °C, which stops the fan cycling on and off every few seconds.
Tick anything you already have and the total updates.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Logic-level MOSFET used as a fast electronic switch, so a PWM pin can control a motor's speed.
4.7 kΩ pull-up between DATA and VCC; 10 kΩ gate pull-down; 220 Ω series resistor for each LED
Follow the colours: red is power, dark grey is ground, blue is a signal.
laptop_stand_cooler.inoVerify & upload in Electrolark// Temperature-controlled laptop stand fan
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "laptop-stand-cooler"
#include <OneWire.h>
#include <DallasTemperature.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t MOTOR_PIN = 3;
const uint8_t LED_RED = 4;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 40; // laptop undersides sit at 35-50 C
const float HYSTERESIS = 4; // gap that stops rapid on/off switching
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setFan(bool on) { digitalWrite(MOTOR_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (!(probeC > -100)) { statusText = "Sensor error"; return; }
if (!alertOn && probeC > ALERT_LEVEL) alertOn = true;
else if (alertOn && probeC < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "Fan on" : "Cool";
}
void setup() {
Serial.begin(115200);
probes.begin();
pinMode(MOTOR_PIN, OUTPUT);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
probeC = readProbeC();
evaluate();
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setFan(alertOn);
setRedLed(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Gate and drain swapped, or the 10 kΩ gate pull-down is missing.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, Power MOSFET (TO-220, IRLZ44N), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Diodes (Pack of 10, 1N4007), Hobby DC Motor (130 size), Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (laptop_stand_cooler.ino). Install these libraries first: OneWire and DallasTemperature.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹483 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Current-limiting resistors for LEDs; MOSFET switching and flyback diodes.
Ideas that reuse this build: Speed knob instead of on/off and Server rack alarm. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C, status=Cool Probe=26.0C, status=Cool
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.