LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsNetwork cabinets and media cupboards cook quietly. The DS18B20 probe sits by the warmest device, the 7-segment display shows the temperature in large digits on the door, and above 35 °C the relay starts an exhaust fan and the buzzer chirps until the air cools.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
A 12 V fan on the relay pulls hot air out of the rack
Follow the colours: red is power, dark grey is ground, blue is a signal.
Fan + to relay COM, relay NO to adapter +, adapter − to fan −. Keep the fan supply separate from the Uno USB.
server_rack_heat_alarm.inoVerify & upload in Electrolark// Server rack overheat alarm
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "server-rack-heat-alarm"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
const uint8_t BUZZER_PIN = 5;
const uint8_t RELAY_PIN = 6;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
TM1637Display seg(SEG_CLK, SEG_DIO);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 35; // most network gear is rated to 40 C inlet
const float HYSTERESIS = 3; // gap that stops rapid on/off switching
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void updateDisplay() {
{ float segV = probeC; // shows 0.00 to 9.99, then 10.0 to 99.9, with a decimal point
if (segV < 0) seg.showNumberDec((int)round(segV), false);
else {
segV = min(segV, 99.9f);
int n = segV < 10 ? (int)round(segV * 100) : (int)round(segV * 10);
uint8_t s[4] = {seg.encodeDigit(n / 100 % 10), seg.encodeDigit(n / 10 % 10), seg.encodeDigit(n % 10), 0};
s[segV < 10 ? 0 : 1] |= 0x80; // decimal point
seg.setSegments(s);
}
}
}
void evaluate() {
if (!(probeC > -100)) { statusText = "Sensor error"; return; }
if (!alertOn && probeC > ALERT_LEVEL) alertOn = true;
else if (alertOn && probeC < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "HOT" : "OK";
}
void setup() {
Serial.begin(115200);
probes.begin();
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
probeC = readProbeC();
evaluate();
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DS18B20 Waterproof Temperature Probe – 1m Cable, TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, 5V Relay Module with Optocoupler (1 channel), Resistor Assortment Kit (30 Values), 12V DC Brushless Fan 80mm (cooling fan), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (server_rack_heat_alarm.ino). Install these libraries first: OneWire, DallasTemperature and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹949 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Active vs passive buzzers; Isolation, relays and switching higher-power loads; Multiplexed 7-segment displays.
Ideas that reuse this build: Log rack temperature to SD and Wi-Fi alert version. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C, status=OK Probe=26.0C, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.