Component guide · Beginner · 3 min read
ULN2003 Darlington Array

Pinout, Wiring and Limits
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
The ULN2003 is a chip with seven Darlington transistor switches. Each channel sinks up to 500 mA at up to 50 V when its input sees a 3.3 V or 5 V logic HIGH, and built-in diodes clamp coil spikes when the COM pin goes to the load supply. It drives relays, small steppers, solenoids and LED strips from a microcontroller, but drops about 1 V and heats up at high current.
Key specs at a glance
- Channels
- 7 (ULN2803: 8)
- Output current
- 500 mA peak per channel; total limited by package heat
- Output voltage
- Up to 50 V
- Input
- 5 V TTL/CMOS through a built-in 2.7 kΩ resistor; works from 3.3 V
- Saturation drop
- About 0.9 V at 100 mA, 1.1 to 1.6 V at 200 to 350 mA
- Clamp diodes
- Built in, common pin 9 (COM)
Pinout and how it switches
Pins 1 to 7 are inputs, pins 16 to 10 are the matching outputs, pin 8 is ground and pin 9 is COM. Each output is a low-side switch: connect the load from the positive supply to an output pin, and the chip connects that pin to ground when its input is HIGH. The ULN2003 cannot source current, so it cannot drive a load that is wired to ground.
Connect the chip's ground to both the microcontroller ground and the load supply ground. For inductive loads such as relays, motors and solenoids, connect COM to the load's positive supply so the internal flyback diodes can absorb the voltage spike when the coil turns off.
Current, heat and when to use a MOSFET instead
The 500 mA figure is a per-channel peak. The plastic package can only shed about 1 W or so, so several channels running hard at once will overheat. For example, four channels at 300 mA with a 1.2 V drop is about 1.4 W, which is too much for continuous use. You can parallel two channels for more current, but a logic-level MOSFET is far more efficient above roughly 300 mA per load.
The roughly 1 V drop also matters at low supply voltages: a 5 V relay sees only about 4 V. Most relays still pull in, but check the coil's minimum operate voltage.
Common uses
- The blue 28BYJ-48 stepper driver board is a ULN2003 with four LEDs; see the 28BYJ-48 guide.
- Driving several 5 V or 12 V relays from a 3.3 V ESP32.
- Switching 12 V LED strips, buzzers or small solenoids.
- Multiplexed displays, where it sinks the common lines.
The ULN2803 is the same idea with eight channels in an 18-pin package, which is handy for an 8-bit port or a 74HC595.
Try it: Power dissipation calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Wiring the load to ground instead of to the positive supply.
- Leaving COM unconnected with relays or motors.
- Running many channels near 500 mA and overheating the chip.
- Forgetting a common ground between the logic and load supplies.
- Ignoring the 1 V drop on a low-voltage load.
Frequently asked questions
Can an ESP32 or Raspberry Pi drive a ULN2003?
Yes. The input switches reliably at 3.3 V, though output current at 3.3 V drive is slightly lower than at 5 V.
Do I need flyback diodes with a ULN2003?
No extra diodes are needed if pin 9 (COM) is connected to the positive supply of the coil loads.
What is the difference between ULN2003 and ULN2803?
The ULN2803 has eight channels in an 18-pin package; the ULN2003 has seven in a 16-pin package. Ratings are similar.
Why does my load only get 11 V from a 12 V supply?
Darlington outputs do not switch fully to ground; expect a 0.9 to 1.6 V drop depending on current.
Can a ULN2003 drive a NEMA 17 stepper?
No. NEMA 17 motors are bipolar and need an H-bridge driver such as the A4988 or TMC2209.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 161 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


