Component guide · Intermediate · 3 min read
TXS0108E 8-Channel Level Shifter

Pinout, Wiring and Limits
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The TXS0108E is an 8-channel bidirectional logic level shifter. It connects 1.2 to 3.6 V signals on the A side to 1.65 to 5.5 V signals on the B side, with automatic direction sensing and speeds up to tens of Mbps. It suits SPI, UART and parallel buses, but it does not work well with I2C or with lines that have strong pull-up resistors or heavy loads.
Key specs at a glance
- Channels
- 8 bidirectional
- A side (VA)
- 1.2 to 3.6 V, must be the lower voltage
- B side (VB)
- 1.65 to 5.5 V
- Speed
- Up to about 60 Mbps push-pull, 2 Mbps open-drain
- Enable
- OE pin: HIGH to enable (tie to VA)
- Internal pull-ups
- About 10 kΩ when the output is high (4 kΩ while driving)
What the TXS0108E level shifter is
Each channel senses which side is driving and copies the level to the other side. It uses one-shot accelerators to speed up edges, which is why it is fast but also why external pull-up resistors below about 50 kΩ or long, loaded wires can confuse it.
For I2C and other open-drain lines, the simple BSS138 MOSFET shifter is more reliable.
TXS0108E level shifter pinout
The pins on the TXS0108E level shifter and what each one does.
| Pin | Function |
|---|---|
| VA | Low-voltage supply, 1.2 to 3.6 V (VA must be at or below VB) |
| VB | High-voltage supply, 1.65 to 5.5 V |
| GND | Common ground |
| OE | Output enable, HIGH = on (tie to VA, often via 10 kΩ) |
| A1 to A8 | Low-voltage side signals |
| B1 to B8 | High-voltage side signals |
- VA
- Low-voltage supply, 1.2 to 3.6 V (VA must be at or below VB)
- VB
- High-voltage supply, 1.65 to 5.5 V
- GND
- Common ground
- OE
- Output enable, HIGH = on (tie to VA, often via 10 kΩ)
- A1 to A8
- Low-voltage side signals
- B1 to B8
- High-voltage side signals
Wiring the TXS0108E level shifter
Always connect VA to the lower voltage and VB to the higher one. Leave OE low only if you want all outputs off (high impedance).
| TXS0108E level shifter pin | Arduino Uno | ESP32 |
|---|---|---|
| VA | 3.3V side (from the 3.3 V device) | 3V3 |
| VB | 5V | 5V device supply |
| GND | GND | GND |
| OE | To VA | To 3V3 |
| A1 to A4 | 3.3 V device pins | GPIO 18, 19, 23, 5 (SPI) |
| B1 to B4 | D13, D12, D11, D10 (SPI) | 5 V device pins |
- VA
- Arduino Uno:
- 3.3V side (from the 3.3 V device)
- ESP32:
- 3V3
- VB
- Arduino Uno:
- 5V
- ESP32:
- 5V device supply
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- OE
- Arduino Uno:
- To VA
- ESP32:
- To 3V3
- A1 to A4
- Arduino Uno:
- 3.3 V device pins
- ESP32:
- GPIO 18, 19, 23, 5 (SPI)
- B1 to B4
- Arduino Uno:
- D13, D12, D11, D10 (SPI)
- ESP32:
- 5 V device pins
Example code
The shifter needs no code; drive the bus as normal. Measure A1 with a multimeter to confirm it reads about 3.3 V when D7 is HIGH.
// Wire Uno D7 to B1, and an LED + 1k resistor from A1 to GND.
// With VA = 3.3 V the LED sees a 3.3 V HIGH.
void setup() { pinMode(7, OUTPUT); }
void loop() {
digitalWrite(7, HIGH); delay(500);
digitalWrite(7, LOW); delay(500);
}Setup and tuning
reversing the rails stops it working.
remove or raise pull-up resistors (50 kΩ or more) on shifted lines.
long wires and heavy loads cause oscillation; keep traces short.
use a BSS138 shifter instead; the TXS0108E often fails with I2C pull-ups.
What you need
Shop this list5 of 6 found in our store · ₹709
TXS0108E 8-Channel Level Shifter: the part this guide coversTXS0108E 8-Channel Level Shifter₹74- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- Logic level shifting: the methods and when to use each.
- BSS138 4-channel shifter: best for I2C and slow open-drain lines.
- Voltage divider: simplest one-way 5 V to 3.3 V shift for a single input.
Common mistakes to avoid
- Using it for I2C and getting stuck or garbled lines.
- Swapping VA and VB, so VA is the higher voltage.
- Leaving OE floating.
- Driving LEDs or other loads straight from the outputs.
Frequently asked questions
Does the TXS0108E work with I2C?
Often not reliably; its auto-direction circuit struggles with I2C pull-ups. Use a BSS138 shifter.
Which side is 3.3 V?
The A side (VA) is always the lower voltage, the B side (VB) the higher.
What is the OE pin for?
Output enable: HIGH turns the channels on, LOW puts them in high impedance.
Is it good for SPI?
Yes, it is fast enough for SPI displays and SD cards in most projects.
Can it drive a WS2812B strip?
It can work for short wires, but a 74AHCT125 buffer is more reliable for LED data.
Parts for this guide
Projects that use it
Put this into practice: 2 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- TXS0108E 8-bit bidirectional voltage-level translator datasheet (Texas Instruments)
- TI application note on effects of pull-up resistors on TXS translators
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

