Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsA step up from the OLED: the ST7735 TFT shows each reading in a different colour with a blue title bar, bright enough to read across a room. The DHT22 and BMP280 share the sensing. A good first colour-display project because the library does the hard work.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Measures barometric pressure (±1 hPa) and temperature over I²C.
For modules without a regulator on 5 V boards
Follow the colours: red is power, dark grey is ground, blue is a signal.
colour_tft_weather_dashboard.inoVerify & upload in Electrolark// Colour TFT weather dashboard
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "colour-tft-weather-dashboard"
#include <DHT.h>
#include <Wire.h>
#include <Adafruit_BMP280.h>
#include <SPI.h>
#include <Adafruit_GFX.h>
#include <Adafruit_ST7735.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t TFT_CS = 3;
const uint8_t TFT_DC = 4;
const uint8_t TFT_RST = 5;
DHT dht(DHT_PIN, DHT22);
Adafruit_BMP280 bmp;
Adafruit_ST7735 tft(TFT_CS, TFT_DC, TFT_RST);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
float pressHpa = 0;
float bmpC = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
static bool drawn = false;
if (!drawn) {
tft.fillScreen(ST77XX_BLACK);
tft.fillRect(0, 0, 160, 18, ST77XX_BLUE);
tft.setTextColor(ST77XX_WHITE);
tft.setTextSize(1);
tft.setCursor(4, 5);
tft.print(F("Weather"));
tft.setTextColor(ST77XX_CYAN);
tft.setCursor(4, 28);
tft.print(F("Temp"));
tft.setTextColor(ST77XX_CYAN);
tft.setCursor(4, 48);
tft.print(F("Humidity"));
tft.setTextColor(ST77XX_CYAN);
tft.setCursor(4, 68);
tft.print(F("Pressure"));
drawn = true;
}
tft.setTextColor(ST77XX_WHITE, ST77XX_BLACK);
tft.setTextSize(2);
tft.setCursor(70, 24);
tft.print(tempC, 1);
tft.print(F(" C"));
tft.print(F(" "));
tft.setCursor(70, 44);
tft.print(humidity, 0);
tft.print(F("%"));
tft.print(F(" "));
tft.setCursor(70, 64);
tft.print(pressHpa, 1);
tft.print(F(" hPa"));
tft.print(F(" "));
tft.setTextSize(1);
tft.setTextColor(ST77XX_YELLOW, ST77XX_BLACK);
tft.setCursor(4, 118);
tft.print(statusText);
tft.print(F(" "));
}
void setup() {
Serial.begin(115200);
dht.begin();
if (!bmp.begin(0x76) && !bmp.begin(0x77)) Serial.println(F("BMP280 not found"));
tft.initR(INITR_BLACKTAB);
tft.setRotation(1);
tft.fillScreen(ST77XX_BLACK);
tft.setTextWrap(false);
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
pressHpa = bmp.readPressure() / 100.0f;
bmpC = bmp.readTemperature();
statusText = (!isnan(tempC) && !isnan(humidity)) ? "OK" : "Sensor error";
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.print(F(", Pressure="));
Serial.print(pressHpa, 1);
Serial.print(F("hPa"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Check SDA/SCL are not swapped. Run an I²C scanner sketch to confirm the address.
SCK/SDA on the wrong pins or RES not wired. Use the hardware SPI pins named in the table.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DHT22 Temperature & Humidity Sensor, BMP280 Temperature & Barometric Pressure Sensor Module, SPI TFT / IPS Colour Display Module, 4-Channel Logic Level Converter (BSS138), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (colour_tft_weather_dashboard.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, Adafruit BMP280 Library, Adafruit ST7735 and ST7789 Library and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹927 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
SPI colour displays; Single-wire digital sensors and why some sensors need slow polling; The I²C bus and device addresses.
Ideas that reuse this build: Mono OLED version and Wi-Fi dashboard. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=26.9C, Humidity=55%, Pressure=1008.0hPa
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.