Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsA single large reading on the TFT, the kind of display you glance at from the sofa. The DHT11 updates every two seconds and the screen redraws only the number, so there is no flicker.
Tick anything you already have and the total updates.
Measures temperature (±2 °C) and humidity (±5 %).
For modules without a regulator on 5 V boards
Follow the colours: red is power, dark grey is ground, blue is a signal.
tft_room_climate_display.inoVerify & upload in Electrolark// Big-digit room climate display
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "tft-room-climate-display"
#include <DHT.h>
#include <SPI.h>
#include <Adafruit_GFX.h>
#include <Adafruit_ST7735.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t TFT_CS = 3;
const uint8_t TFT_DC = 4;
const uint8_t TFT_RST = 5;
DHT dht(DHT_PIN, DHT11);
Adafruit_ST7735 tft(TFT_CS, TFT_DC, TFT_RST);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
const unsigned long READ_EVERY_MS = 1500;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
static bool drawn = false;
if (!drawn) {
tft.fillScreen(ST77XX_BLACK);
tft.fillRect(0, 0, 160, 18, ST77XX_BLUE);
tft.setTextColor(ST77XX_WHITE);
tft.setTextSize(1);
tft.setCursor(4, 5);
tft.print(F("Room"));
tft.setTextColor(ST77XX_CYAN);
tft.setCursor(4, 30);
tft.print(F("Temp"));
drawn = true;
}
tft.setTextColor(ST77XX_WHITE, ST77XX_BLACK);
tft.setTextSize(3);
tft.setCursor(4, 50);
tft.print(tempC, 1);
tft.print(F(" C"));
tft.print(F(" "));
tft.setTextSize(1);
tft.setTextColor(ST77XX_YELLOW, ST77XX_BLACK);
tft.setCursor(4, 118);
tft.print(statusText);
tft.print(F(" "));
}
void setup() {
Serial.begin(115200);
dht.begin();
tft.initR(INITR_BLACKTAB);
tft.setRotation(1);
tft.fillScreen(ST77XX_BLACK);
tft.setTextWrap(false);
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
statusText = (!isnan(tempC) && !isnan(humidity)) ? "OK" : "Sensor error";
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
SCK/SDA on the wrong pins or RES not wired. Use the hardware SPI pins named in the table.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), DHT11 Digital Temperature & Humidity Sensor Module, SPI TFT / IPS Colour Display Module, 4-Channel Logic Level Converter (BSS138), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (tft_room_climate_display.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, Adafruit ST7735 and ST7789 Library and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹692 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
SPI colour displays; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Add humidity and pressure and 7-segment version. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=26.9C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.