Component guide · Beginner · 3 min read
Wireless Charging Transmitter Modules (15W Type-C, XKT-412) and LTC4124 Charger

By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Wireless charging modules transfer power through a magnetic field between two coils. The 15 W Type-C module is a Qi transmitter for phones; the XKT-412 kit is a transmitter and receiver pair that sends 5 V across a few millimetres to power or charge DIY devices. The LTC4124 is a tiny charger IC that charges a Li-ion cell directly from a wireless receiver coil.
Key specs at a glance
- 15 W module
- Qi transmitter, USB-C input (QC/PD 9 to 12 V for 15 W)
- XKT-412
- 5 V 2 A, transmitter and receiver coils
- LTC4124
- Wireless Li-ion charger, up to 100 mA
- Distance
- A few mm (best touching)
- Efficiency
- About 60 to 75 percent
- Heat
- Coils and metal nearby warm up
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 115W Wireless Charging Transmitter Module, Type-C₹250
Option 2Wireless Charging Transmitter Module with Coil₹609
Option 3Analog Devices LTC4124 Wireless Li-Ion Charger IC₹750
What the Wireless charging transmitter module is
Wireless charging modules are Qi-style transmitter and receiver coil pairs that send 5 V power across a small gap, for sealed devices, phone chargers and rotating parts.
Alignment and distance matter most. Keep metal away from the coils; it heats and reduces power.
XKT-412 is not Qi compatible; it pairs only with its own receiver.
Wireless charging transmitter module pinout
The pins on the Wireless charging transmitter module and what each one does.
| Pin | Function |
|---|---|
| Input | USB-C or 5 V |
| TX coil | Transmitter |
| RX coil / output | Receiver output (XKT-412) |
- Input
- USB-C or 5 V
- TX coil
- Transmitter
- RX coil / output
- Receiver output (XKT-412)
Wiring the Wireless charging transmitter module
Connect the Wireless charging transmitter module like this.
| Wireless charging transmitter module pin | 15 W Qi | XKT-412 |
|---|---|---|
| Input | USB-C PD charger | 5 V 2 A supply |
| Output | Phone (Qi) | Receiver 5 V to device |
- Input
- 15 W Qi:
- USB-C PD charger
- XKT-412:
- 5 V 2 A supply
- Output
- 15 W Qi:
- Phone (Qi)
- XKT-412:
- Receiver 5 V to device
Example code
A minimal sketch to check the part works.
1. Connect the battery first, then the input source.
2. Measure charge voltage at the battery terminals.
3. Watch cell temperature during the first full charge.Setup and tuning
use matching transmitter and receiver modules.
keep the coils aligned and within a few mm.
feed the transmitter the rated input (often 5 or 12 V).
stay within the receiver's current rating (often 0.5 to 1 A).
keep metal away from coils; it heats up.
What you need
Shop this list5 of 5 found in our store · ₹11,95,667
15W Wireless Charging Transmitter Module, Type-C: the part this guide covers15W Wireless Charging Transmitter Module, Type-C₹250
Wireless Charging Transmitter Module with Coil: another version this guide coversWireless Charging Transmitter Module with Coil₹609
Analog Devices LTC4124 Wireless Li-Ion Charger IC: another version this guide coversAnalog Devices LTC4124 Wireless Li-Ion Charger IC₹750
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
18650 Li-ion rechargeable cell: the cell to charge or protect18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
Alternatives and when to choose them
- TP4056 charger: wired.
- USB-C PD triggers.
Common mistakes to avoid
- Metal between coils.
- Misaligned coils.
- Overloading the receiver.
- Charging batteries without a charger IC.
Frequently asked questions
How far can wireless charging modules transfer power?
Usually a few mm to about 1 cm, with aligned coils.
Can it charge a battery directly?
Not directly; add a charger module after the receiver output.
Why does the transmitter get hot?
Misaligned coils, metal near the coils, or too much load.
Can I power a rotating part?
Yes. Coils on the axis can power slowly rotating parts without slip rings.
Does it work with phones?
Qi-compatible transmitter modules can charge Qi phones.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
