LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsLong seminars and cultural programmes leave a closed hall stuffy by the second hour. The air sensor at the back of the hall lights the red LED and beeps above 60 %, a cue to open exits or run the extractors during the break.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Heated sensor that responds to ammonia, CO₂, alcohol, smoke and benzene.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
auditorium_stuffy_air_alarm.inoVerify & upload in Electrolark// Auditorium stuffy air alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "auditorium-stuffy-air-alarm"
// ---- pins ----
const uint8_t AIR_PIN = A0;
const uint8_t BUZZER_PIN = 2;
const uint8_t LED_RED = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// ---- latest readings ----
int airPct = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 60; // a full hall with the doors shut gets stuffy and makes people drowsy
const float HYSTERESIS = 10; // gap that stops rapid on/off switching
const unsigned long WARMUP_MS = 60000UL; // sensor warm-up
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (millis() < WARMUP_MS) { alertOn = false; statusText = "Warming up"; return; }
if (!alertOn && airPct > ALERT_LEVEL) alertOn = true;
else if (alertOn && airPct < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "STUFFY" : "Fresh";
}
void setup() {
Serial.begin(115200);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
airPct = (int)(analogRead(AIR_PIN) * 100L / ADC_MAX);
evaluate();
Serial.print(F("Air="));
Serial.print(airPct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), Winsen MQ135 Air Quality Gas Sensor, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (auditorium_stuffy_air_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹566 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Analog sensors, ADCs and warm-up drift; Current-limiting resistors for LEDs.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Ideas that reuse this build: Wi-Fi version and SMS version. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Air=29%, status=Warming up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.