LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsAir pressure falls ahead of rain and storms and rises in settled weather. The BMP180 costs only a few rupees and shows pressure on the OLED. Note the number each morning and you will soon see a pattern: a steady fall of 3 hPa or more in three hours often means rain is coming.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures air pressure over I²C.
Follow the colours: red is power, dark grey is ground, blue is a signal.
bmp180_pressure_station.inoVerify & upload in Electrolark// BMP180 pressure and weather watcher
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "bmp180-pressure-station"
#include <Wire.h>
#include <Adafruit_BMP085_U.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_BMP085_Unified bmp = Adafruit_BMP085_Unified(10085);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float pressHpa = 0;
float bmpC = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "OK";
float bmp180Hpa() { sensors_event_t e; bmp.getEvent(&e); return e.pressure; }
float bmp180C() { float t = 0; bmp.getTemperature(&t); return t; }
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Pressure"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Pressure: "));
oled.print(pressHpa, 1);
oled.print(F(" hPa"));
oled.setCursor(0, 24);
oled.print(F("Temp: "));
oled.print(bmpC, 1);
oled.print(F(" C"));
oled.display();
}
void setup() {
Serial.begin(115200);
if (!bmp.begin()) Serial.println(F("BMP180 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
pressHpa = bmp180Hpa();
bmpC = bmp180C();
Serial.print(F("Pressure="));
Serial.print(pressHpa, 1);
Serial.print(F("hPa"));
Serial.print(F(", Temp="));
Serial.print(bmpC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x77.
That is the sea-level figure. Use the change from your first reading to see height and weather.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), BMP180 Digital Barometric Pressure Sensor Module – I2C Interface, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (bmp180_pressure_station.ino). Install these libraries first: Adafruit BMP085 Unified, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹452 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Barometric pressure and altitude; Drawing text on an I²C display.
Ideas that reuse this build: Balcony weather pressure logger and Class barometer weather. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Pressure=1007.8hPa, Temp=25.9C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.