LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsFriction turns movement into heat. Point the infrared sensor at your palms, rub them hard for ten seconds and measure again. Then try rubbing a coin on paper and a rubber on a desk.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared thermometer: measures the temperature of whatever it points at without touching it (field of view about 90°).
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_friction_heat.inoVerify & upload in Electrolark// Heat from friction
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "class-friction-heat"
#include <Wire.h>
#include <Adafruit_MLX90614.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
Adafruit_MLX90614 mlx;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
float objC = 0;
float ambC = 0;
const unsigned long READ_EVERY_MS = 300;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
{ float segV = objC; // shows 0.00 to 9.99, then 10.0 to 99.9, with a decimal point
if (segV < 0) seg.showNumberDec((int)round(segV), false);
else {
segV = min(segV, 99.9f);
int n = segV < 10 ? (int)round(segV * 100) : (int)round(segV * 10);
uint8_t s[4] = {seg.encodeDigit(n / 100 % 10), seg.encodeDigit(n / 10 % 10), seg.encodeDigit(n % 10), 0};
s[segV < 10 ? 0 : 1] |= 0x80; // decimal point
seg.setSegments(s);
}
}
}
void setup() {
Serial.begin(115200);
if (!mlx.begin()) Serial.println(F("MLX90614 not found"));
seg.setBrightness(5);
seg.clear();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
objC = mlx.readObjectTempC();
ambC = mlx.readAmbientTempC();
Serial.print(F("Object="));
Serial.print(objC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
You are too far away, so the sensor sees mostly background. Move closer.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Ask students to predict which rubs warm up the most, then rank them. Rubbing harder versus faster is a good extension.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), MLX90614 IR Non-Contact Temperature Sensor Module, TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 30 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_friction_heat.ino). Install these libraries first: Adafruit MLX90614 Library and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,006 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Friction and heat; Energy transfer.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Ideas that reuse this build: Hand vs room and Non-contact IR thermometer. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Object=34.9C Object=35.0C Object=35.1C Object=35.0C Object=35.0C Object=34.9C Object=35.1C Object=35.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.