LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe TTP223 senses the capacitance change of a finger. Students stack layers between finger and pad and find how thick a material can be before it stops working.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Capacitive touch pad: works through thin plastic, glass or wood, so you can hide it inside an enclosure.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_touch_capacitance.inoVerify & upload in Electrolark// Which materials are touch-sensitive?
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "class-touch-capacitance"
// ---- pins ----
const uint8_t TOUCH_PIN = 2;
const uint8_t LED_YELLOW = 3;
// ---- latest readings ----
bool touched = false;
const unsigned long READ_EVERY_MS = 50;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 500; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void evaluate() {
if (touched) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "TOUCH" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(TOUCH_PIN, INPUT);
pinMode(LED_YELLOW, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
touched = digitalRead(TOUCH_PIN) == HIGH;
evaluate();
Serial.print(F("Touch="));
Serial.print(touched ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setYellowLed(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Ground the enclosure or keep long wires away from the pad.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Add sheets one at a time and count how many it takes.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Capacitive Touch Sensor Module (TTP223), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 30 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_touch_capacitance.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹319 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Capacitance; Insulators.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Touch=no, status=OK Touch=no, status=OK Touch=no, status=OK Touch=no, status=OK Touch=no, status=OK Touch=no, status=OK Touch=no, status=OK Touch=no, status=OK Touch=no, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.