LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsInsulin, some medicines and lab samples must stay between 2 and 8 °C. Drop the probe into the cool box, keep the display on the lid, and the buzzer goes off the moment the inside passes 8 °C so you can add ice before anything spoils.
Tick anything you already have and the total updates.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
4.7 kΩ pull-up between DATA and VCC; 220 Ω series resistor for each LED
Follow the colours: red is power, dark grey is ground, blue is a signal.
cold_chain_vaccine_alarm.inoVerify & upload in Electrolark// Cold-chain box temperature alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "cold-chain-vaccine-alarm"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
const uint8_t BUZZER_PIN = 5;
const uint8_t LED_RED = 6;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 8; // vaccines and insulin are stored at 2-8 C
const float HYSTERESIS = 1; // gap that stops rapid on/off switching
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
{ float segV = probeC; // shows 0.00 to 9.99, then 10.0 to 99.9, with a decimal point
if (segV < 0) seg.showNumberDec((int)round(segV), false);
else {
segV = min(segV, 99.9f);
int n = segV < 10 ? (int)round(segV * 100) : (int)round(segV * 10);
uint8_t s[4] = {seg.encodeDigit(n / 100 % 10), seg.encodeDigit(n / 10 % 10), seg.encodeDigit(n % 10), 0};
s[segV < 10 ? 0 : 1] |= 0x80; // decimal point
seg.setSegments(s);
}
}
}
void evaluate() {
if (!(probeC > -100)) { statusText = "Sensor error"; return; }
if (!alertOn && probeC > ALERT_LEVEL) alertOn = true;
else if (alertOn && probeC < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "TOO WARM" : "OK";
}
void setup() {
Serial.begin(115200);
probes.begin();
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
probeC = readProbeC();
evaluate();
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (cold_chain_vaccine_alarm.ino). Install these libraries first: OneWire, DallasTemperature and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹432 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Active vs passive buzzers; Current-limiting resistors for LEDs; Multiplexed 7-segment displays.
Ideas that reuse this build: Freezer alarm and Logger with timestamps. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C, status=TOO WARM Probe=26.0C, status=TOO WARM
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.