LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsFragile goods are damaged by rough handling, but no one admits it. Tape the logger inside the parcel and the SD card records the shake level every half second. Afterwards you can see exactly when the big knocks happened.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Three-axis accelerometer that feels gravity and bumps, so it can measure tilt angles and detect knocks, drops and vibration.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
courier_parcel_shock_logger.inoVerify & upload in Electrolark// Parcel shock and drop logger
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "courier-parcel-shock-logger"
#include <Wire.h>
#include <Adafruit_ADXL345_U.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t SD_CS = 10;
Adafruit_ADXL345_Unified accel = Adafruit_ADXL345_Unified(12345);
float adxX = 0, adxY = 0, adxZ = 1; // in g
RTC_DS3231 rtc;
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
const unsigned long LOG_EVERY_MS = 500UL; // one row per 0 s
unsigned long lastLog = 0;
bool cardOk = false;
void readAdxl() {
sensors_event_t e;
accel.getEvent(&e);
adxX = e.acceleration.x / 9.81f; adxY = e.acceleration.y / 9.81f; adxZ = e.acceleration.z / 9.81f;
}
float adxPitch() { return atan2(-adxX, sqrt(adxY * adxY + adxZ * adxZ)) * 57.3f; }
float adxRoll() { return atan2(adxY, adxZ) * 57.3f; }
float adxShake() { float m = sqrt(adxX * adxX + adxY * adxY + adxZ * adxZ); return fabs(m - 1.0f); }
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(pitchDeg, 1);
f.print(',');
f.print(rollDeg, 1);
f.print(',');
f.print(shakeG, 2);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
if (!accel.begin()) Serial.println(F("ADXL345 not found"));
accel.setRange(ADXL345_RANGE_4_G);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Pitch(deg),Roll(deg),Shake(g)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
pitchDeg = (readAdxl(), adxPitch());
rollDeg = adxRoll();
shakeG = adxShake();
Serial.print(F("Pitch="));
Serial.print(pitchDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Roll="));
Serial.print(rollDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Shake="));
Serial.print(shakeG, 2);
Serial.print(F("g"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x53 (0x1D if the ALT pin is high).
Keep the board still while it starts, and check pitch and roll are not swapped for your mounting.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), ADXL345 Digital Acceleration Sensor Module – I2C/SPI, 3.3V/5V, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (courier_parcel_shock_logger.ino). Install these libraries first: Adafruit ADXL345, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,474 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Accelerometers, tilt angles and shock detection; Real-time clocks and backup batteries; SPI devices and CSV logging.
Ideas that reuse this build: Machine vibration logger and Tilt tamper alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.