LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe laser sensor rides on the drill head and looks down at the table. As you lower the quill, the display counts down the distance in millimetres. Note the reading when the bit touches the work, then drill down by the depth you need. Repeatable holes without a fiddly depth stop.
Keep the wires clear of the spinning chuck, and wear eye protection when drilling.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Laser time-of-flight sensor: measures 3 cm to about 1.2 m with millimetre resolution in a tiny package.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
drill_press_depth_readout.inoVerify & upload in Electrolark// Drill press depth readout
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "drill-press-depth-readout"
#include <Wire.h>
#include <Adafruit_VL53L0X.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
Adafruit_VL53L0X tof;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
int tofMm = 0;
const unsigned long READ_EVERY_MS = 100;
unsigned long lastRead = 0;
const char* statusText = "OK";
int readTofMm() {
VL53L0X_RangingMeasurementData_t m;
tof.rangingTest(&m, false);
return (m.RangeStatus != 4) ? m.RangeMilliMeter : -1;
}
void updateDisplay() {
seg.showNumberDec((int)round(tofMm), false);
}
void setup() {
Serial.begin(115200);
if (!tof.begin()) Serial.println(F("VL53L0X not found"));
seg.setBrightness(5);
seg.clear();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tofMm = readTofMm();
statusText = (tofMm > 0) ? "OK" : "Sensor error";
Serial.print(F("Range="));
Serial.print(tofMm);
Serial.print(F("mm"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Target is out of range or too dark/shiny. Try a white card within 1 m.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), VL53L0X ToF Laser Distance Sensor Module, TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (drill_press_depth_readout.ino). Install these libraries first: Adafruit_VL53L0X and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹419 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Laser ranging vs ultrasonic ranging; Multiplexed 7-segment displays.
Keep the wires clear of the spinning chuck, and wear eye protection when drilling.
Ideas that reuse this build: Laser distance meter and ToF height gauge. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Range=400mm Range=402mm Range=400mm Range=402mm Range=402mm Range=401mm Range=400mm Range=400mm Range=399mm
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.