LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsFish do best when the water is stable. The log shows temperature swings between day and night, when the water goes cloudy, when evaporation drops the level, and how many hours of light the tank gets.
Keep all electronics above the water line and use only low-voltage modules in contact with water.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Shines light through the water gap and measures how much gets through.
A sealed float with a switch inside.
Digital light sensor that reports brightness in lux, the same unit used for room and street lighting.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
fish_tank_water_logger.inoVerify & upload in Electrolark// Fish tank water logger
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "fish-tank-water-logger"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Wire.h>
#include <BH1750.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t TURB_PIN = A0;
const uint8_t FLOAT_PIN = 3;
const uint8_t SD_CS = 10;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
BH1750 lightMeter;
RTC_DS3231 rtc;
// ---- latest readings ----
float probeC = 0;
int clarityPct = 0;
bool floatUp = false;
float lux = 0;
const unsigned long LOG_EVERY_MS = 120000UL; // one row per 120 s
unsigned long lastLog = 0;
bool cardOk = false;
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(probeC, 1);
f.print(',');
f.print(clarityPct);
f.print(',');
f.print(floatUp);
f.print(',');
f.print(lux, 0);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
probes.begin();
pinMode(FLOAT_PIN, INPUT_PULLUP);
Wire.begin();
if (!lightMeter.begin()) Serial.println(F("BH1750 not found"));
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Probe(C),Clarity(%),Float up,Light(lx)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
probeC = readProbeC();
clarityPct = (int)(analogRead(TURB_PIN) * 100L / ADC_MAX);
floatUp = digitalRead(FLOAT_PIN) == LOW;
lux = lightMeter.readLightLevel();
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", Clarity="));
Serial.print(clarityPct);
Serial.print(F("%"));
Serial.print(F(", Float up="));
Serial.print(floatUp ? F("yes") : F("no"));
Serial.print(F(", Light="));
Serial.print(lux, 0);
Serial.print(F("lx"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Shade the sensor gap; stray light adds to the reading.
Flip the float over (the arrow or marking points up) or swap the logic in the sketch.
Clear any dirt or sludge from around the float so it moves freely.
Check SDA and SCL are not swapped. An I²C scanner should show 0x23 (0x5C if the ADDR pin is tied high).
Check the wiring and power, then try again. A reading of 0 in a dark room is normal.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
11 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, Asair AZDM01 Turbidity Sensor Module – Analog, Square Float Switch, 2 m Cable, IP68 – Pump Tank Level Sensor, GY-302 BH1750 Light Intensity Module – I2C Interface, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, Resistor Assortment Kit (30 Values), microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 4–5 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (fish_tank_water_logger.ino). Install these libraries first: OneWire, DallasTemperature, BH1750, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,990 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Level switches and pull-up resistors; Lux, lumens and the I²C bus; Optical sensing and calibration references; Real-time clocks and backup batteries.
Keep all electronics above the water line and use only low-voltage modules in contact with water.
Ideas that reuse this build: Aquarium water clarity alarm and Aquarium top-up alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD card ready Probe=26.0C, Clarity=29%, Float up=no, Light=319lx Probe=26.0C, Clarity=30%, Float up=no, Light=320lx
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.