LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsGlue a small magnet to anything that spins and hold the Hall sensor near it. The Nano counts passes for a second and shows the RPM on the display. Change MAGNETS_PER_REV if you use more than one magnet for slow shafts.
Tick anything you already have and the total updates.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
hall_tachometer.inoVerify & upload in Electrolark// Hall-effect tachometer
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "hall-tachometer"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t HALL_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
bool magnet = false;
unsigned long pulses = 0, windowStart = 0;
bool wasMagnet = false;
const int MAGNETS_PER_REV = 1;
void setup() {
Serial.begin(115200);
pinMode(HALL_PIN, INPUT);
seg.setBrightness(5);
seg.clear();
}
void loop() {
bool m = digitalRead(HALL_PIN) == LOW;
if (m && !wasMagnet) pulses++;
wasMagnet = m;
if (millis() - windowStart >= 1000) {
unsigned long rpm = pulses * 60UL / MAGNETS_PER_REV;
seg.showNumberDec(min(rpm, 9999UL));
Serial.print(rpm); Serial.println(F(" rpm"));
pulses = 0; windowStart = millis();
}
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Flip the magnet and adjust the trimmer.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), Linear Magnetic Hall Sensor Module – LM393, TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (hall_tachometer.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹351 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Magnetic sensing; Multiplexed 7-segment displays.
Ideas that reuse this build: Bike speedometer and NEMA 17 speed control. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0 rpm 0 rpm
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.