Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsThe joystick shield plugs straight onto an Uno with no wiring. This sketch prints the X and Y position as values from −100 to 100 ten times a second: open the Serial Plotter and you see two lines dance as you move the stick. The starting point for every joystick project.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Plug-on shield with a two-axis thumb joystick, four big buttons and sockets for nRF24L01 and Bluetooth modules.
Follow the colours: red is power, dark grey is ground, blue is a signal.
joystick_serial_tester.inoVerify & upload in Electrolark// Joystick shield tester
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "joystick-serial-tester"
// ---- pins ----
const uint8_t JOY_X = A0;
const uint8_t JOY_Y = A1;
const uint8_t JOY_BTN = 8;
const uint8_t BTN_A = 2;
const uint8_t BTN_B = 3;
const uint8_t BTN_C = 4;
const uint8_t BTN_D = 5;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// ---- latest readings ----
int joyX = 0;
int joyY = 0;
const unsigned long READ_EVERY_MS = 100;
unsigned long lastRead = 0;
const char* statusText = "OK";
void setup() {
Serial.begin(115200);
pinMode(JOY_BTN, INPUT_PULLUP); pinMode(BTN_A, INPUT_PULLUP); pinMode(BTN_B, INPUT_PULLUP);
pinMode(BTN_C, INPUT_PULLUP); pinMode(BTN_D, INPUT_PULLUP);
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
joyX = map(analogRead(JOY_X), 0, ADC_MAX, -100, 100);
joyY = map(analogRead(JOY_Y), 0, ADC_MAX, -100, 100);
Serial.print(F("Joystick X="));
Serial.print(joyX);
Serial.print(F(", Joystick Y="));
Serial.print(joyY);
Serial.println();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The shield voltage switch is on 3.3 V; set it to 5 V for the Uno.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
3 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA and Joystick Shield for Arduino Robotics & Game Control. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 20 minutes. The build on this page has 6 steps.
No. This page has the complete, tested code (joystick_serial_tester.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹372 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog joysticks and shields.
Ideas that reuse this build: Pan-tilt camera mount, Etch-a-sketch on an OLED and Radio-controlled car. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Joystick X=-39, Joystick Y=-39 Joystick X=-40, Joystick Y=-39 Joystick X=-39, Joystick Y=-39 Joystick X=-39, Joystick Y=-39 Joystick X=-39, Joystick Y=-39 Joystick X=-39, Joystick Y=-40 Joystick X=-39, Joystick Y=-39 Joystick X=-39, Joystick Y=-39
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.