Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe joystick moves a pen one pixel at a time across the 128×64 OLED and the line stays behind it, just like the red toy. Press button A on the shield to shake it clean. A gentle introduction to graphics coordinates.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Plug-on shield with a two-axis thumb joystick, four big buttons and sockets for nRF24L01 and Bluetooth modules.
Follow the colours: red is power, dark grey is ground, blue is a signal.
joystick_etch_a_sketch.inoVerify & upload in Electrolark// Etch-a-sketch on an OLED
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "joystick-etch-a-sketch"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t JOY_X = A0;
const uint8_t JOY_Y = A1;
const uint8_t JOY_BTN = 8;
const uint8_t BTN_A = 2;
const uint8_t BTN_B = 3;
const uint8_t BTN_C = 4;
const uint8_t BTN_D = 5;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
int joyX = 0;
int joyY = 0;
int px = 64, py = 32;
unsigned long lastMove = 0;
void setup() {
Serial.begin(115200);
pinMode(JOY_BTN, INPUT_PULLUP); pinMode(BTN_A, INPUT_PULLUP); pinMode(BTN_B, INPUT_PULLUP);
pinMode(BTN_C, INPUT_PULLUP); pinMode(BTN_D, INPUT_PULLUP);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
oled.drawPixel(px, py, SSD1306_WHITE); oled.display();
}
void loop() {
if (digitalRead(BTN_A) == LOW) { oled.clearDisplay(); px = 64; py = 32; } // button A shakes the sketch clean
if (millis() - lastMove < 25) return;
lastMove = millis();
joyX = map(analogRead(JOY_X), 0, ADC_MAX, -100, 100);
joyY = map(analogRead(JOY_Y), 0, ADC_MAX, -100, 100);
if (joyX > 30) px++; else if (joyX < -30) px--;
if (joyY > 30) py--; else if (joyY < -30) py++;
px = constrain(px, 0, 127); py = constrain(py, 0, 63);
oled.drawPixel(px, py, SSD1306_WHITE);
oled.display();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The shield voltage switch is on 3.3 V; set it to 5 V for the Uno.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Joystick Shield for Arduino Robotics & Game Control, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (joystick_etch_a_sketch.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹606 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog joysticks and shields; Drawing text on an I²C display.
Ideas that reuse this build: Snake on an LED matrix and Joystick tester. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.