LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA small magnet on the key ring hangs over a Hall sensor on the key hook. When the front-door reed switch opens and the keys are still hanging, the buzzer beeps for three seconds. Take the keys and the door opens silently.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Glass switch whose contacts close when a magnet is near.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
key_hook_reminder.inoVerify & upload in Electrolark// Did you take your keys? door reminder
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "key-hook-reminder"
// ---- pins ----
const uint8_t REED_PIN = 2;
const uint8_t HALL_PIN = 3;
const uint8_t BUZZER_PIN = 4;
// ---- latest readings ----
bool doorOpen = false;
bool magnet = false;
const unsigned long READ_EVERY_MS = 50;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 3000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void evaluate() {
if (doorOpen && magnet) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "KEYS!" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(REED_PIN, INPUT_PULLUP);
pinMode(HALL_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
doorOpen = digitalRead(REED_PIN) == HIGH;
magnet = digitalRead(HALL_PIN) == LOW;
evaluate();
Serial.print(F("Door open="));
Serial.print(doorOpen ? F("yes") : F("no"));
Serial.print(F(", Magnet="));
Serial.print(magnet ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Bring the magnet within 1 cm and align it parallel to the glass body.
Flip the magnet and adjust the trimmer.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Y213 Reed Switch Normally Open (glass), Linear Magnetic Hall Sensor Module – LM393, Active Buzzer Module 3.3–5V, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (key_hook_reminder.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹346 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Magnetic sensing; Pull-up resistors and reed switches.
Ideas that reuse this build: Door-open alarm and Deadbolt locked indicator. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
, Magnet=no, status=OK Door open=yes, Magnet=no, status=OK Door open=yes, Magnet=no, status=OK Door open=yes, Magnet=no, status=OK Door open=yes, Magnet=no, status=OK Door open=yes, Magnet=no, status=OK Door open=yes, Magnet=no, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.