LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsAfter a scare, the question is always what happened and when. The log keeps LPG, smoke, flame and heat readings every 20 seconds so you can find out and fix the cause.
A learning aid, not a certified detector. Keep proper fire alarms fitted.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Heated sensor that responds to LPG, propane and natural gas, used in kitchen leak alarms.
Heated tin-oxide sensor that responds to LPG, smoke, butane and hydrogen.
Infrared photodiode tuned to 760–1100 nm, the light given off by flames, with a comparator for an on/off output.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
kitchen_safety_station_logger.inoVerify & upload in Electrolark// Kitchen safety station logger
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "kitchen-safety-station-logger"
#include <DHT.h>
#include <Wire.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t LPG_PIN = A0;
const uint8_t GAS_PIN = A1;
const uint8_t FLAME_PIN = 2;
const uint8_t DHT_PIN = 3;
const uint8_t SD_CS = 10;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
DHT dht(DHT_PIN, DHT22);
RTC_DS3231 rtc;
// ---- latest readings ----
int lpgPct = 0;
int gasPct = 0;
bool flame = false;
float tempC = 0;
float humidity = 0;
const unsigned long LOG_EVERY_MS = 20000UL; // one row per 20 s
unsigned long lastLog = 0;
bool cardOk = false;
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(lpgPct);
f.print(',');
f.print(gasPct);
f.print(',');
f.print(flame);
f.print(',');
f.print(tempC, 1);
f.print(',');
f.print(humidity, 0);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
pinMode(FLAME_PIN, INPUT);
dht.begin();
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,LPG(%),Gas(%),Flame,Temp(C),Humidity(%)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
lpgPct = (int)(analogRead(LPG_PIN) * 100L / ADC_MAX);
gasPct = (int)(analogRead(GAS_PIN) * 100L / ADC_MAX);
flame = digitalRead(FLAME_PIN) == LOW;
tempC = dht.readTemperature();
humidity = dht.readHumidity();
Serial.print(F("LPG="));
Serial.print(lpgPct);
Serial.print(F("%"));
Serial.print(F(", Gas="));
Serial.print(gasPct);
Serial.print(F("%"));
Serial.print(F(", Flame="));
Serial.print(flame ? F("yes") : F("no"));
Serial.print(F(", Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Sunlight contains strong IR. Shade the sensor or lower the sensitivity with the trimmer.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Nano CH340 Development Board (Soldered), MQ-5 Methane LPG Propane Gas Sensor Module – Analog/Digital Output, MQ-2 Smoke / LPG Gas Sensor Module – Analog/Digital Output, Flame Sensor Module – LM393, Digital/Analog Output, DHT22 Temperature & Humidity Sensor, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 4–5 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (kitchen_safety_station_logger.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,647 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Comparator outputs and sensitivity trimmers; Real-time clocks and backup batteries; SPI devices and CSV logging; Single-wire digital sensors and why some sensors need slow polling.
A learning aid, not a certified detector. Keep proper fire alarms fitted. This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Ideas that reuse this build: Canteen kitchen smoke logger and LPG store room gas logger. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
%, Flame=no, Temp=26.9C, Humidity=55% LPG=30%, Gas=29%, Flame=no, Temp=27.0C, Humidity=55% LPG=30%, Gas=30%, Flame=no, Temp=27.0C, Humidity=55%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.