LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA soldering or chemistry bench has hot things, fumes and a room that changes through the day. The log helps you see the pattern and decide where to add ventilation or a safer layout.
A learning and comparison aid, not a certified instrument.
Keep the board away from heat and flammable liquids.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared thermometer: measures the temperature of whatever it points at without touching it (field of view about 90°).
Reads a K-type thermocouple probe up to 1,000 °C through an amplifier chip, which is the way to measure ovens, kilns, soldering irons and engines.
Heated tin-oxide sensor that responds strongly to alcohol vapour, used in breath testers and fermentation checks.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
lab_bench_heat_and_fume_logger.inoVerify & upload in Electrolark// Lab bench heat and fume logger
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "lab-bench-heat-and-fume-logger"
#include <Wire.h>
#include <Adafruit_MLX90614.h>
#include <max6675.h>
#include <DHT.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t TC_SCK = 2;
const uint8_t TC_CS = 3;
const uint8_t TC_SO = 4;
const uint8_t ALCOHOL_PIN = A0;
const uint8_t DHT_PIN = 5;
const uint8_t SD_CS = 10;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Adafruit_MLX90614 mlx;
MAX6675 thermocouple(TC_SCK, TC_CS, TC_SO);
DHT dht(DHT_PIN, DHT22);
RTC_DS3231 rtc;
// ---- latest readings ----
float objC = 0;
float ambC = 0;
float probeC = 0;
int alcoholPct = 0;
float tempC = 0;
float humidity = 0;
const unsigned long LOG_EVERY_MS = 20000UL; // one row per 20 s
unsigned long lastLog = 0;
bool cardOk = false;
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(objC, 1);
f.print(',');
f.print(ambC, 1);
f.print(',');
f.print(probeC, 0);
f.print(',');
f.print(alcoholPct);
f.print(',');
f.print(tempC, 1);
f.print(',');
f.print(humidity, 0);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
if (!mlx.begin()) Serial.println(F("MLX90614 not found"));
dht.begin();
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Object(C),Ambient(C),Probe(C),Alcohol(%),Temp(C),Humidity(%)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
objC = mlx.readObjectTempC();
ambC = mlx.readAmbientTempC();
probeC = thermocouple.readCelsius();
alcoholPct = (int)(analogRead(ALCOHOL_PIN) * 100L / ADC_MAX);
tempC = dht.readTemperature();
humidity = dht.readHumidity();
Serial.print(F("Object="));
Serial.print(objC, 1);
Serial.print(F("C"));
Serial.print(F(", Ambient="));
Serial.print(ambC, 1);
Serial.print(F("C"));
Serial.print(F(", Probe="));
Serial.print(probeC, 0);
Serial.print(F("C"));
Serial.print(F(", Alcohol="));
Serial.print(alcoholPct);
Serial.print(F("%"));
Serial.print(F(", Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
You are too far away, so the sensor sees mostly background. Move closer.
The thermocouple is not connected or its plus and minus wires are swapped. Check the screw terminals.
The module also senses its own temperature at the cold junction. Keep it away from the heat you are measuring.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Nano CH340 Development Board (Soldered), MLX90614 IR Non-Contact Temperature Sensor Module, MAX6675 Module with K-Type Thermocouple Probe, 50 cm Cable, MQ-3 Alcohol Gas Detector Sensor Module – Analog & Digital Output, DHT22 Temperature & Humidity Sensor, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 4–5 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (lab_bench_heat_and_fume_logger.ino). Install these libraries first: Adafruit MLX90614 Library, MAX6675 library, DHT sensor library, Adafruit Unified Sensor, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹2,504 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Contactless infrared temperature measurement; Real-time clocks and backup batteries; SPI devices and CSV logging; Single-wire digital sensors and why some sensors need slow polling.
A learning and comparison aid, not a certified instrument. Keep the board away from heat and flammable liquids. Not a medical device. Readings are for learning and must not be used for diagnosis.
Ideas that reuse this build: Alcohol fumes colour ring and Stepper furnace temperature dial. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
% Object=34.9C, Ambient=26.1C, Probe=180C, Alcohol=30%, Temp=27.1C, Humidity=55% Object=35.0C, Ambient=26.0C, Probe=180C, Alcohol=29%, Temp=27.1C, Humidity=55%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.