LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsMany fungal diseases need the leaf surface to stay wet for hours. The rain board, set at an angle among the plants, works as a leaf-wetness sensor: dew or rain makes the reading climb. After a wet spell the yellow light stays on for six hours as a reminder to walk the crop and check for spots.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Comb-patterned plate whose resistance drops when water bridges the tracks.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
leaf_wetness_disease_alert.inoVerify & upload in Electrolark// Leaf wetness alert for crop disease
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "leaf-wetness-disease-alert"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t RAIN_PIN = A0;
const uint8_t LED_YELLOW = 2;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
int wetPct = 0;
const unsigned long READ_EVERY_MS = 60000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 30; // long periods of wet leaves raise fungal disease risk
const float HYSTERESIS = 10; // gap that stops rapid on/off switching
const unsigned long HOLD_MS = 21600000; // keep the alert on this long after the last trigger
unsigned long lastTrigger = 0;
bool levelHigh = false;
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Rain "));
lcd.print(wetPct);
lcd.print(F("%"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!levelHigh && wetPct > ALERT_LEVEL) levelHigh = true;
else if (levelHigh && wetPct < ALERT_LEVEL - HYSTERESIS) levelHigh = false;
if (levelHigh) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "Spray check" : "Dry leaves";
}
void setup() {
Serial.begin(115200);
pinMode(LED_YELLOW, OUTPUT);
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
wetPct = (int)(100 - analogRead(RAIN_PIN) * 100L / ADC_MAX);
evaluate();
Serial.print(F("Rain="));
Serial.print(wetPct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setYellowLed(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Dry the plate and clean off residue. Powering it only when reading slows corrosion.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), HS-S09-PB Rain Sensor Kit – Analog/Digital Output, Through-Hole LED Pack (Pack of 10), LCD1602 16x2 Character LCD (blue, with I2C adapter), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (leaf_wetness_disease_alert.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹628 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Current-limiting resistors for LEDs; Resistive sensing and corrosion.
Ideas that reuse this build: Rain alert and Greenhouse climate LCD. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.