LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe reed switch sits on the letterbox flap. When the flap lifts, the Nano keeps a yellow LED on for ten minutes, long enough to notice from the kitchen that something arrived. Run a long pair of wires and the LED can sit inside the house.
Tick anything you already have and the total updates.
Glass switch whose contacts close when a magnet is near.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mailbox_notifier.inoVerify & upload in Electrolark// Letterbox flap notifier
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "mailbox-notifier"
// ---- pins ----
const uint8_t REED_PIN = 2;
const uint8_t LED_YELLOW = 3;
// ---- latest readings ----
bool doorOpen = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 600000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void evaluate() {
if (doorOpen) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "POST!" : "Empty";
}
void setup() {
Serial.begin(115200);
pinMode(REED_PIN, INPUT_PULLUP);
pinMode(LED_YELLOW, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
doorOpen = digitalRead(REED_PIN) == HIGH;
evaluate();
Serial.print(F("Door open="));
Serial.print(doorOpen ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setYellowLed(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Bring the magnet within 1 cm and align it parallel to the glass body.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Y213 Reed Switch Normally Open (glass), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (mailbox_notifier.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹323 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Pull-up resistors and reed switches.
Ideas that reuse this build: Wi-Fi mailbox that messages you and Door-open alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Door open=yes, status=POST! Door open=yes, status=POST!
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.