Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsA flame sensor near the electrical panel, a PIR over the counter and a reed switch on the shutter all feed one Mega. Any of them sounds the buzzer and lights the LCD alarm for 20 seconds, and the Serial Monitor shows the state of each sensor so you can see which one tripped. Switch it on when you close and off when you open.
A learning project. A real shop needs a certified fire alarm and smoke detectors.
Tick anything you already have and the total updates.
Infrared photodiode tuned to 760–1100 nm, the light given off by flames, with a comparator for an on/off output.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Glass switch whose contacts close when a magnet is near.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_after_hours_shop_console.inoVerify & upload in Electrolark// After-hours shop fire and intruder console on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-after-hours-shop-console"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t FLAME_PIN = 22;
const uint8_t PIR_PIN = 23;
const uint8_t REED_PIN = 24;
const uint8_t BUZZER_PIN = 25;
const uint8_t LED_RED = 26;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
bool flame = false;
bool motion = false;
bool doorOpen = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 20000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
const unsigned long WARMUP_MS = 30000UL; // sensor warm-up
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Flame "));
lcd.print(flame ? F("YES") : F("no"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Moti "));
lcd.print(motion ? F("YES") : F("no"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (millis() < WARMUP_MS) { alertOn = false; statusText = "Warming up"; return; }
if ((flame || motion || doorOpen)) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "ALARM" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(FLAME_PIN, INPUT);
pinMode(PIR_PIN, INPUT);
pinMode(REED_PIN, INPUT_PULLUP);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
flame = digitalRead(FLAME_PIN) == LOW;
motion = digitalRead(PIR_PIN) == HIGH;
doorOpen = digitalRead(REED_PIN) == HIGH;
evaluate();
Serial.print(F("Flame="));
Serial.print(flame ? F("yes") : F("no"));
Serial.print(F(", Motion="));
Serial.print(motion ? F("yes") : F("no"));
Serial.print(F(", Door open="));
Serial.print(doorOpen ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Sunlight contains strong IR. Shade the sensor or lower the sensitivity with the trimmer.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Bring the magnet within 1 cm and align it parallel to the glass body.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, Flame Sensor Module – LM393, Digital/Analog Output, HC-SR501 PIR Motion Detector Sensor Module, Y213 Reed Switch Normally Open (glass), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), LCD1602 16x2 Character LCD (blue, with I2C adapter), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (mega_after_hours_shop_console.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,342 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Comparator outputs and sensitivity trimmers; Current-limiting resistors for LEDs; Digital inputs and sensor hold time.
A learning project. A real shop needs a certified fire alarm and smoke detectors.
Ideas that reuse this build: Mega security console and SMS shop shutter alert. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Flame=no, Motion=no, Door open=yes, status=Warming up Flame=no, Motion=no, Door open=yes, status=Warming up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.