Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsThree questions every farmer asks at the pump: is the motor running hot, is water actually flowing, and has the field had enough? A probe on the motor body, a flow sensor on the outlet and a soil sensor in the field answer all three on one LCD, with every reading also printed to the Serial Monitor. The Mega has pins to spare for a relay or SMS module later.
Keep the panel in a closed box away from water and the motor starter. The pump itself stays on its own starter; this panel only measures.
Tick anything you already have and the total updates.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
Capacitive probe that measures soil moisture without exposed metal, so it does not corrode like resistive probes.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_farm_pump_house_panel.inoVerify & upload in Electrolark// Farm pump-house panel on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-farm-pump-house-panel"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t ONEWIRE_PIN = 22;
const uint8_t FLOW_PIN = 2;
const uint8_t SOIL_PIN = A0;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
const int SOIL_DRY = 520; // reading in dry air: calibrate
const int SOIL_WET = 260; // reading in a glass of water: calibrate
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float probeC = 0;
float flowLpm = 0;
float litres = 0;
int soilPct = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Probe "));
lcd.print(probeC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Flow "));
lcd.print(flowLpm, 1);
lcd.print(F(" L/min"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
probes.begin();
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
probeC = readProbeC();
flowLpm = readFlowLpm();
litres = litresTotal;
soilPct = constrain(map(analogRead(SOIL_PIN), SOIL_DRY, SOIL_WET, 0, 100), 0, 100);
statusText = (probeC > -100) ? "OK" : "Sensor error";
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", Flow="));
Serial.print(flowLpm, 1);
Serial.print(F("L/min"));
Serial.print(F(", Soil="));
Serial.print(soilPct);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Calibrate: note the raw reading in dry air and in water, and put them in SOIL_DRY and SOIL_WET.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, DS18B20 Waterproof Temperature Probe – 1m Cable, YF-S201 Water Flow Sensor 1–30 L/min, Capacitive Soil Moisture Sensor – 3.3V/5V Analog Output, LCD1602 16x2 Character LCD (blue, with I2C adapter), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (mega_farm_pump_house_panel.ino). Install these libraries first: OneWire, DallasTemperature and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,469 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Calibrating an analog sensor with map(); Character displays and I²C backpacks; Interrupts and counting pulses.
Keep the panel in a closed box away from water and the motor starter. The pump itself stays on its own starter; this panel only measures.
Ideas that reuse this build: Machine hour meter and Farm drip irrigation controller. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C, Flow=0.0L/min, Soil=82% Probe=26.0C, Flow=0.0L/min, Soil=82%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.