LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsService intervals are given in running hours, but few small machines have a meter. A vibration sensor stuck to the machine body knows when it is running; the Nano adds up the minutes, saves them so a power cut loses nothing, and shows the total and the hours left to the next service. When it is due, it chirps while the machine runs. Hold the button for three seconds after servicing.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Spring-type vibration switch with a comparator: the output goes high while it is being shaken.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
machine_hour_meter.inoVerify & upload in Electrolark// Machine hour meter with service reminder
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "machine-hour-meter"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#include <EEPROM.h>
// ---- pins ----
const uint8_t VIB_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t BUTTON_PIN = 4;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
bool shake = false;
const unsigned long SERVICE_HOURS = 250; // hours between services for the machine
const unsigned long QUIET_MS = 20000; // no vibration for this long = stopped
unsigned long runMinutes = 0, sinceService = 0; // both saved in EEPROM
unsigned long lastShake = 0, runMs = 0, lastTick = 0, lastShow = 0;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void save() { EEPROM.put(0, runMinutes); EEPROM.put(4, sinceService); }
void show(bool running) {
char buf[17];
snprintf(buf, sizeof(buf), "Total %5lu.%lu h ", runMinutes / 60, (runMinutes % 60) / 6);
lcd.setCursor(0, 0); lcd.print(buf);
unsigned long left = SERVICE_HOURS * 60 > sinceService ? (SERVICE_HOURS * 60 - sinceService) / 60 : 0;
if (left == 0) snprintf(buf, sizeof(buf), "SERVICE DUE ");
else snprintf(buf, sizeof(buf), "%s Svc in %4luh", running ? "RUN" : "off", left);
lcd.setCursor(0, 1); lcd.print(buf);
}
void setup() {
Serial.begin(115200);
pinMode(VIB_PIN, INPUT);
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(BUTTON_PIN, INPUT_PULLUP);
EEPROM.get(0, runMinutes); EEPROM.get(4, sinceService);
if (runMinutes == 0xFFFFFFFFUL) { runMinutes = 0; sinceService = 0; save(); } // a fresh board reads all ones
setBuzzer(false);
}
void loop() {
shake = digitalRead(VIB_PIN) == HIGH;
if (shake) lastShake = millis();
bool running = lastShake && millis() - lastShake < QUIET_MS;
unsigned long now = millis();
if (running) runMs += now - lastTick;
lastTick = now;
if (runMs >= 60000UL) { // one more minute of running
runMs -= 60000UL; runMinutes++; sinceService++;
if (runMinutes % 10 == 0) save(); // write every 10 minutes to spare the EEPROM
}
bool due = sinceService >= SERVICE_HOURS * 60;
setBuzzer(due && running && (millis() / 1000) % 30 == 0); // a short chirp every 30 s while it runs overdue
if (digitalRead(BUTTON_PIN) == LOW) { // hold 3 s after a service to restart the countdown
unsigned long t = millis();
while (digitalRead(BUTTON_PIN) == LOW && millis() - t < 3000) delay(10);
if (millis() - t >= 3000) { sinceService = 0; save(); Serial.println(F("Service logged")); }
}
if (millis() - lastShow > 1000) { lastShow = millis(); show(running); Serial.print(runMinutes); Serial.println(F(" min total")); }
delay(5);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the trimmer and tap harder; loosely mounted modules absorb vibration.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), SW-420 Vibration Sensor Module – Digital Output, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (machine_hour_meter.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹437 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Debouncing noisy digital signals; Pull-ups and debouncing.
Ideas that reuse this build: Generator hour meter and Belt slip alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0 min total 0 min total
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.