LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA slipping V-belt glazes, heats and breaks, and the driven machine slows down first. A magnet on the driven pulley passes the Hall sensor once a turn; the Nano shows the RPM and, once the machine has been running for ten seconds, alarms if the speed drops below 75 % of normal.
Fit the sensor and magnet with the machine switched off and locked out. Keep cables clear of belts and pulleys.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
belt_slip_alarm.inoVerify & upload in Electrolark// Belt slip and shaft speed alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "belt-slip-alarm"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t HALL_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
const uint8_t BUZZER_PIN = 5;
const uint8_t LED_RED = 6;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
bool magnet = false;
const unsigned long NORMAL_RPM = 900; // measure the healthy speed and enter it here
const int SLIP_PCT = 75; // alarm below this share of normal speed
const int MAGNETS_PER_REV = 1;
unsigned long pulses = 0, windowStart = 0, runningSince = 0, rpm = 0;
bool wasMagnet = false;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(HALL_PIN, INPUT);
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
setBuzzer(false);
setRedLed(false);
}
void loop() {
magnet = digitalRead(HALL_PIN) == LOW;
if (magnet && !wasMagnet) pulses++;
wasMagnet = magnet;
if (millis() - windowStart >= 1000) {
rpm = pulses * 60UL / MAGNETS_PER_REV;
pulses = 0; windowStart = millis();
seg.showNumberDec(min(rpm, 9999UL));
if (rpm == 0) runningSince = 0;
else if (!runningSince) runningSince = millis();
Serial.print(rpm); Serial.println(F(" rpm"));
}
bool started = runningSince && millis() - runningSince > 10000; // ignore the first 10 s while it speeds up
bool slipping = started && rpm < NORMAL_RPM * SLIP_PCT / 100;
setRedLed(slipping);
setBuzzer(slipping && (millis() / 200) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Flip the magnet and adjust the trimmer.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), Linear Magnetic Hall Sensor Module – LM393, TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (belt_slip_alarm.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹426 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Magnetic sensing; Multiplexed 7-segment displays.
Fit the sensor and magnet with the machine switched off and locked out. Keep cables clear of belts and pulleys.
Ideas that reuse this build: Hall tachometer and Machine hour meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0 rpm 0 rpm
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.