Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsA sensor on the machine foot reads vibration and a probe on the body reads temperature. The Mega logs both every ten seconds to a CSV file. After a few weeks, the file shows how the machine ages: slowly rising vibration or temperature means a bearing or belt is wearing.
Tick anything you already have and the total updates.
Six-axis motion sensor: a three-axis accelerometer that feels gravity and bumps, and a three-axis gyro that measures how fast it turns.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_machine_health_logger.inoVerify & upload in Electrolark// Machine health logger on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-machine-health-logger"
#include <Wire.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <OneWire.h>
#include <DallasTemperature.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 22;
const uint8_t SD_CS = 53;
Adafruit_MPU6050 mpu;
sensors_event_t accEvt, gyrEvt, tmpEvt;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
RTC_DS3231 rtc;
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
float probeC = 0;
const unsigned long LOG_EVERY_MS = 10000UL; // one row per 10 s
unsigned long lastLog = 0;
bool cardOk = false;
void readImu() { mpu.getEvent(&accEvt, &gyrEvt, &tmpEvt); }
float pitchDegNow() { return atan2(accEvt.acceleration.x, sqrt(accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z)) * 57.3f; }
float rollDegNow() { return atan2(accEvt.acceleration.y, accEvt.acceleration.z) * 57.3f; }
float shakeGNow() { float a = sqrt(accEvt.acceleration.x * accEvt.acceleration.x + accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z) / 9.81f; return fabs(a - 1.0f); }
float gyroZNow() { return gyrEvt.gyro.z * 57.3f; } // turning speed in degrees per second
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(pitchDeg, 1);
f.print(',');
f.print(rollDeg, 1);
f.print(',');
f.print(shakeG, 2);
f.print(',');
f.print(probeC, 1);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
if (!mpu.begin()) Serial.println(F("MPU6050 not found"));
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
mpu.setGyroRange(MPU6050_RANGE_500_DEG);
mpu.setFilterBandwidth(MPU6050_BAND_21_HZ);
probes.begin();
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Pitch(deg),Roll(deg),Shake(g),Probe(C)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
pitchDeg = (readImu(), pitchDegNow());
rollDeg = rollDegNow();
shakeG = shakeGNow();
probeC = readProbeC();
Serial.print(F("Pitch="));
Serial.print(pitchDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Roll="));
Serial.print(rollDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Shake="));
Serial.print(shakeG, 2);
Serial.print(F("g"));
Serial.print(F(", Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped. An I²C scanner should show 0x68 (0x69 if AD0 is tied high).
Keep I²C wires short, add a 100 nF capacitor across VCC and GND, and mount the board away from motor wires.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, GY-521 MPU6050 6-Axis Gyro and Accelerometer Module, DS18B20 Waterproof Temperature Probe – 1m Cable, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, Resistor Assortment Kit (30 Values), microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (mega_machine_health_logger.ino). Install these libraries first: Adafruit MPU6050, Adafruit Unified Sensor, OneWire, DallasTemperature, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹2,324 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Accelerometers, gyros and tilt angles; Real-time clocks and backup batteries; SPI devices and CSV logging.
Ideas that reuse this build: Motor vibration monitor and Motor temperature monitor. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD card ready Pitch=0.0deg, Roll=0.0deg, Shake=0.00g, Probe=26.0C Pitch=0.0deg, Roll=0.0deg, Shake=0.00g, Probe=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.