LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsBearings and loose mounts show up as vibration long before a breakdown. The MPU6050 bolted to the motor foot reads the shaking in g; the LCD shows it and the buzzer warns when it rises well above normal. Write down the reading each week to see the trend.
Mount the sensor with the machine isolated and locked out. Keep cables away from shafts and belts.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Six-axis motion sensor: a three-axis accelerometer that feels gravity and bumps, and a three-axis gyro that measures how fast it turns.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
motor_vibration_monitor.inoVerify & upload in Electrolark// Motor and pump vibration monitor
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "motor-vibration-monitor"
#include <Wire.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t BUZZER_PIN = 2;
Adafruit_MPU6050 mpu;
sensors_event_t accEvt, gyrEvt, tmpEvt;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 0.5; // a sharp rise from the normal level points to a worn bearing or a loose mount
const float HYSTERESIS = 0.1; // gap that stops rapid on/off switching
void readImu() { mpu.getEvent(&accEvt, &gyrEvt, &tmpEvt); }
float pitchDegNow() { return atan2(accEvt.acceleration.x, sqrt(accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z)) * 57.3f; }
float rollDegNow() { return atan2(accEvt.acceleration.y, accEvt.acceleration.z) * 57.3f; }
float shakeGNow() { float a = sqrt(accEvt.acceleration.x * accEvt.acceleration.x + accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z) / 9.81f; return fabs(a - 1.0f); }
float gyroZNow() { return gyrEvt.gyro.z * 57.3f; } // turning speed in degrees per second
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Shake "));
lcd.print(shakeG, 2);
lcd.print(F(" g"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!alertOn && shakeG > ALERT_LEVEL) alertOn = true;
else if (alertOn && shakeG < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "CHECK BEARING" : "Normal";
}
void setup() {
Serial.begin(115200);
if (!mpu.begin()) Serial.println(F("MPU6050 not found"));
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
mpu.setGyroRange(MPU6050_RANGE_500_DEG);
mpu.setFilterBandwidth(MPU6050_BAND_21_HZ);
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
pitchDeg = (readImu(), pitchDegNow());
rollDeg = rollDegNow();
shakeG = shakeGNow();
evaluate();
Serial.print(F("Shake="));
Serial.print(shakeG, 2);
Serial.print(F("g"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped. An I²C scanner should show 0x68 (0x69 if AD0 is tied high).
Keep I²C wires short, add a 100 nF capacitor across VCC and GND, and mount the board away from motor wires.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, GY-521 MPU6050 6-Axis Gyro and Accelerometer Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (motor_vibration_monitor.ino). Install these libraries first: Adafruit MPU6050, Adafruit Unified Sensor and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹627 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Accelerometers, gyros and tilt angles; Active vs passive buzzers; Character displays and I²C backpacks.
Mount the sensor with the machine isolated and locked out. Keep cables away from shafts and belts.
Ideas that reuse this build: Phone dashboard version and Machine hour meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Shake=0.00g, status=Normal Shake=0.00g, status=Normal Shake=0.00g, status=Normal Shake=0.00g, status=Normal Shake=0.00g, status=Normal Shake=0.00g, status=Normal Shake=0.00g, status=Normal Shake=0.00g, status=Normal
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.