LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsBirds are sensitive to heat, damp air and ammonia from the litter. The log shows when the shed runs hot or stuffy through the day and night so you can plan fans, ventilation and cleaning.
A learning and comparison aid, not a certified instrument.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Heated sensor that responds to ammonia, CO₂, alcohol, smoke and benzene.
Digital light sensor that reports brightness in lux, the same unit used for room and street lighting.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
poultry_house_climate_logger.inoVerify & upload in Electrolark// Poultry house climate logger
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "poultry-house-climate-logger"
#include <DHT.h>
#include <Wire.h>
#include <BH1750.h>
#include <OneWire.h>
#include <DallasTemperature.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t AIR_PIN = A0;
const uint8_t ONEWIRE_PIN = 3;
const uint8_t SD_CS = 10;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
DHT dht(DHT_PIN, DHT22);
BH1750 lightMeter;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
RTC_DS3231 rtc;
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
int airPct = 0;
float lux = 0;
float probeC = 0;
const unsigned long LOG_EVERY_MS = 60000UL; // one row per minute
unsigned long lastLog = 0;
bool cardOk = false;
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(tempC, 1);
f.print(',');
f.print(humidity, 0);
f.print(',');
f.print(airPct);
f.print(',');
f.print(lux, 0);
f.print(',');
f.print(probeC, 1);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
dht.begin();
Wire.begin();
if (!lightMeter.begin()) Serial.println(F("BH1750 not found"));
probes.begin();
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Temp(C),Humidity(%),Air(%),Light(lx),Probe(C)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
airPct = (int)(analogRead(AIR_PIN) * 100L / ADC_MAX);
lux = lightMeter.readLightLevel();
probeC = readProbeC();
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.print(F(", Air="));
Serial.print(airPct);
Serial.print(F("%"));
Serial.print(F(", Light="));
Serial.print(lux, 0);
Serial.print(F("lx"));
Serial.print(F(", Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Check SDA and SCL are not swapped. An I²C scanner should show 0x23 (0x5C if the ADDR pin is tied high).
Check the wiring and power, then try again. A reading of 0 in a dark room is normal.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
11 parts: Nano CH340 Development Board (Soldered), DHT22 Temperature & Humidity Sensor, Winsen MQ135 Air Quality Gas Sensor, GY-302 BH1750 Light Intensity Module – I2C Interface, DS18B20 Waterproof Temperature Probe – 1m Cable, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, Resistor Assortment Kit (30 Values), microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 4–5 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (poultry_house_climate_logger.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, BH1750, OneWire, DallasTemperature, RTClib, plus 1 more.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,860 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Analog sensors, ADCs and warm-up drift; Lux, lumens and the I²C bus; Real-time clocks and backup batteries; SPI devices and CSV logging.
A learning and comparison aid, not a certified instrument. This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Ideas that reuse this build: Poultry shed night guard with animal calls and Air quality data logger. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD card ready Temp=26.9C, Humidity=55%, Air=30%, Light=320lx, Probe=26.0C Temp=27.1C, Humidity=55%, Air=30%, Light=320lx, Probe=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.