LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA float switch at the top of the barrel rises when it is full. The green light and chirp tell you to switch the downpipe to the garden or the next barrel and stop water going to waste.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A sealed float with a switch inside.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
rain_barrel_full_alarm.inoVerify & upload in Electrolark// Rain barrel full alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "rain-barrel-full-alarm"
// ---- pins ----
const uint8_t FLOAT_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_GREEN = 4;
// ---- latest readings ----
bool floatUp = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 3000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void evaluate() {
if (floatUp) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "BARREL FULL" : "Filling";
}
void setup() {
Serial.begin(115200);
pinMode(FLOAT_PIN, INPUT_PULLUP);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_GREEN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
floatUp = digitalRead(FLOAT_PIN) == LOW;
evaluate();
Serial.print(F("Float up="));
Serial.print(floatUp ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Flip the float over (the arrow or marking points up) or swap the logic in the sketch.
Clear any dirt or sludge from around the float so it moves freely.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), Square Float Switch, 2 m Cable, IP68 – Pump Tank Level Sensor, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (rain_barrel_full_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹566 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Level switches and pull-up resistors.
Ideas that reuse this build: Sump pit overflow alarm and Aquarium top-up alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Float up=no, status=Filling Float up=no, status=Filling
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.