LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsPanels lose output as they heat up. The log shows light, UV, air temperature and panel back temperature together, so you can see how much hotter the panel runs than the air and how it follows the sun through the day.
A learning and comparison aid, not a certified instrument.
Keep the electronics out of rain and away from the panel wiring.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Digital light sensor that reports brightness in lux, the same unit used for room and street lighting.
Analog temperature sensor that outputs 10 mV for every degree Celsius, so no library or calibration table is needed.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
rooftop_solar_site_logger.inoVerify & upload in Electrolark// Rooftop solar site logger
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "rooftop-solar-site-logger"
#include <Wire.h>
#include <BH1750.h>
#include <OneWire.h>
#include <DallasTemperature.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t UV_PIN = A0;
const uint8_t LM35_PIN = A1;
const uint8_t ONEWIRE_PIN = 2;
const uint8_t SD_CS = 10;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
BH1750 lightMeter;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
RTC_DS3231 rtc;
// ---- latest readings ----
float lux = 0;
float uvIndex = 0;
float tempC = 0;
float probeC = 0;
const unsigned long LOG_EVERY_MS = 60000UL; // one row per minute
unsigned long lastLog = 0;
bool cardOk = false;
float readLm35C() {
long s = 0;
for (int i = 0; i < 20; i++) s += analogRead(LM35_PIN); // average out the noise
return (s / 20.0f) * VREF * 100.0f / ADC_MAX; // 10 mV per degree C
}
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(lux, 0);
f.print(',');
f.print(uvIndex, 1);
f.print(',');
f.print(tempC, 1);
f.print(',');
f.print(probeC, 1);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
Wire.begin();
if (!lightMeter.begin()) Serial.println(F("BH1750 not found"));
probes.begin();
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Light(lx),UV index,Temp(C),Probe(C)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
lux = lightMeter.readLightLevel();
uvIndex = analogRead(UV_PIN) * VREF / ADC_MAX / 0.1f;
tempC = readLm35C();
probeC = readProbeC();
Serial.print(F("Light="));
Serial.print(lux, 0);
Serial.print(F("lx"));
Serial.print(F(", UV index="));
Serial.print(uvIndex, 1);
Serial.print(F(", Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped. An I²C scanner should show 0x23 (0x5C if the ADDR pin is tied high).
Check the wiring and power, then try again. A reading of 0 in a dark room is normal.
Expected. Take it outside in daylight.
Keep the sensor away from the board regulator and warm parts, and add a 100 nF capacitor from OUT to GND.
The sketch already averages 20 samples. Add the capacitor and shorten the wire.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
11 parts: Nano CH340 Development Board (Soldered), GY-302 BH1750 Light Intensity Module – I2C Interface, GUVA-S12SD UV Sensor Module, LM35D Analog Temperature Sensor Module – Analog Voltage Output, DS18B20 Waterproof Temperature Probe – 1m Cable, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, Resistor Assortment Kit (30 Values), microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 4–5 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (rooftop_solar_site_logger.ino). Install these libraries first: BH1750, OneWire, DallasTemperature, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,849 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Analog temperature sensing and ADC resolution; Converting a voltage to a physical unit; Lux, lumens and the I²C bus; Real-time clocks and backup batteries.
A learning and comparison aid, not a certified instrument. Keep the electronics out of rain and away from the panel wiring.
Ideas that reuse this build: Sunlight hours logger and Solar panel compass aligner. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD card ready Light=319lx, UV index=15.0, Temp=150.1C, Probe=26.0C Light=320lx, UV index=15.0, Temp=150.0C, Probe=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.