LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsAn LM35 taped on the hot outlet pipe shows its surface temperature on the OLED. Watch the reading climb through the morning, so you know when the water is ready and whether cloud or a dirty panel is stopping the tank from reaching full temperature.
Fix the sensor to the outside of the pipe only, with heat-proof tape. Water from a solar heater can scald.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Analog temperature sensor that outputs 10 mV for every degree Celsius, so no library or calibration table is needed.
Follow the colours: red is power, dark grey is ground, blue is a signal.
solar_water_heater_outlet_monitor.inoVerify & upload in Electrolark// Solar water heater outlet monitor
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "solar-water-heater-outlet-monitor"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t LM35_PIN = A0;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float tempC = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readLm35C() {
long s = 0;
for (int i = 0; i < 20; i++) s += analogRead(LM35_PIN); // average out the noise
return (s / 20.0f) * VREF * 100.0f / ADC_MAX; // 10 mV per degree C
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Hot water"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Temp"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(tempC, 1);
oled.print(F(" C"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tempC = readLm35C();
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Keep the sensor away from the board regulator and warm parts, and add a 100 nF capacitor from OUT to GND.
The sketch already averages 20 samples. Add the capacitor and shorten the wire.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), LM35D Analog Temperature Sensor Module – Analog Voltage Output, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (solar_water_heater_outlet_monitor.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹557 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog temperature sensing and ADC resolution; Drawing text on an I²C display.
Fix the sensor to the outside of the pipe only, with heat-proof tape. Water from a solar heater can scald.
Ideas that reuse this build: Geyser outlet pipe hot alarm and LM35 room thermometer. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=150.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.