LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA flow sensor in the supply line measures water every second. The red light comes on whenever water is flowing; if it keeps flowing for more than ten minutes, the buzzer starts. A dripping tap (under 0.3 L/min) is ignored.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
tap_left_running_alarm.inoVerify & upload in Electrolark// Tap left running alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "tap-left-running-alarm"
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t FLOW_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_RED = 4;
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
// ---- latest readings ----
float flowLpm = 0;
float litres = 0;
const unsigned long RUN_LIMIT_MS = 10 * 60000UL; // longest normal use (a bath fill, a bucket)
const float FLOWING_LPM = 0.3; // below this counts as off (a drip)
unsigned long runningSince = 0, lastCheck = 0;
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
setBuzzer(false);
setRedLed(false);
}
void loop() {
if (millis() - lastCheck >= 1000) { // the flow rate is worked out once a second
lastCheck = millis();
flowLpm = readFlowLpm();
if (flowLpm > FLOWING_LPM) { if (!runningSince) runningSince = millis(); }
else runningSince = 0;
Serial.print(F("Flow ")); Serial.print(flowLpm, 1); Serial.print(F(" L/min, running "));
Serial.print(runningSince ? (millis() - runningSince) / 1000 : 0); Serial.println(F(" s"));
}
bool alarm = runningSince && millis() - runningSince > RUN_LIMIT_MS;
setRedLed(runningSince != 0);
setBuzzer(alarm && (millis() / 300) % 2 == 0);
delay(10);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), YF-S201 Water Flow Sensor 1–30 L/min, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (tap_left_running_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹514 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Interrupts and counting pulses.
Ideas that reuse this build: Tap flow rate in the classroom and Water leak alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Flow 0.0 L/min, running 0 s Flow 0.0 L/min, running 0 s
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.