LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsComfort in a ward matters for recovery. The SHT31 on the wall shows the temperature and humidity on an LCD, so a nurse can see when to run the fan or AC, and when the air has become too dry.
A comfort aid, not a medical device. Follow your clinic's rules for room conditions.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Accurate digital temperature (±0.3 °C) and humidity (±2 %) sensor from Sensirion, well suited to long-term room and storage monitoring.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
ward_climate_monitor.inoVerify & upload in Electrolark// Clinic ward climate monitor
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "ward-climate-monitor"
#include <Wire.h>
#include <Adafruit_SHT31.h>
#include <LiquidCrystal_I2C.h>
Adafruit_SHT31 sht31 = Adafruit_SHT31();
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Temp "));
lcd.print(tempC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Humi "));
lcd.print(humidity, 0);
lcd.print(F("%"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
if (!sht31.begin(0x44)) Serial.println(F("SHT31 not found"));
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tempC = sht31.readTemperature();
humidity = sht31.readHumidity();
statusText = (!isnan(tempC) && !isnan(humidity)) ? "OK" : "Sensor error";
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x44 or 0x45.
Keep the sensor out of condensing air and away from heat sources.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), GY-SHT31-D Digital Temperature and Humidity Sensor Module – I2C Interface, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (ward_climate_monitor.ino). Install these libraries first: Adafruit SHT31 Library and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹740 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Calibrated digital humidity sensors; Character displays and I²C backpacks.
A comfort aid, not a medical device. Follow your clinic's rules for room conditions.
Ideas that reuse this build: SHT31 reference climate monitor and Nursery temperature and humidity alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=25.9C, Humidity=55%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.