LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA vibration sensor taped to the machine feels it running. The green LED blinks while the drum turns; when the machine has been still for three minutes after at least five minutes of running, the LED stays on and the buzzer gives three short beeps every 30 seconds until you press the button.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Spring-type vibration switch with a comparator: the output goes high while it is being shaken.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
washing_machine_done_alert.inoVerify & upload in Electrolark// Washing machine finished alert
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "washing-machine-done-alert"
// ---- pins ----
const uint8_t VIB_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_GREEN = 4;
const uint8_t BUTTON_PIN = 5;
// ---- latest readings ----
bool shake = false;
const unsigned long RUN_MIN_MS = 5 * 60000UL; // shaking for at least this long counts as a wash cycle
const unsigned long QUIET_MS = 3 * 60000UL; // this long without vibration means the cycle has ended
unsigned long runStart = 0, lastShake = 0;
bool done = false;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(VIB_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_GREEN, OUTPUT);
pinMode(BUTTON_PIN, INPUT_PULLUP);
setBuzzer(false);
setGreenLed(false);
}
void loop() {
shake = digitalRead(VIB_PIN) == HIGH;
if (shake) { lastShake = millis(); if (!runStart) { runStart = millis(); done = false; Serial.println(F("Cycle started")); } }
if (runStart && millis() - lastShake > QUIET_MS) {
if (lastShake - runStart > RUN_MIN_MS) { done = true; Serial.println(F("Cycle finished")); }
runStart = 0; // a short shake (someone leaning on it) is ignored
}
setGreenLed(done || (runStart && (millis() / 1000) % 2 == 0)); // blinks while running, solid when done
unsigned long t = millis() % 30000; // three beeps every 30 seconds until you press the button
setBuzzer(done && t < 900 && (t / 150) % 2 == 0);
if (done && digitalRead(BUTTON_PIN) == LOW) { done = false; setBuzzer(false); delay(300); }
delay(5);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the trimmer and tap harder; loosely mounted modules absorb vibration.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Long soaks are quiet. Raise QUIET_MS to 10 minutes for machines with a soak phase.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), SW-420 Vibration Sensor Module – Digital Output, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Tactile Push Button Switch, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 11 steps.
No. This page has the complete, tested code (washing_machine_done_alert.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹376 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Debouncing noisy digital signals; Pull-ups and debouncing.
Ideas that reuse this build: Silent vibration doorbell and Vibration table for the classroom. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Cycle started Cycle started
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.