Component guide · Beginner · 3 min read
18650 Power Bank Modules and 5V 2A Charge-Discharge Boards

Build a USB Power Bank
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A power bank module combines a single-cell Li-ion charger, protection and a 5 V boost converter on one board. Add one or more 18650 cells in parallel and you have a USB power bank or a 5 V backup supply for an Arduino, ESP32 or Raspberry Pi Zero. The 2 A charge-discharge boards can charge and power the load at the same time on many versions.
Key specs at a glance
- Cells
- 1S Li-ion (parallel cells allowed)
- Charge
- About 1 to 2 A from USB 5 V
- Output
- 5 V 1 to 2 A
- Protection
- Over-charge, over-discharge, short
- Indicators
- LEDs or capacity display
- Auto off
- Many switch off at low load
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Power Bank Module (18650)₹23
Option 25V 2A Charge-Discharge Integrated Module₹77
What the 18650 power bank module is
A power bank module is one small board that does three jobs for a single lithium cell: it charges the cell from USB, protects it, and boosts its 3.7 V to 5 V USB output.
Many modules turn the output off when the load is under about 50 to 100 mA, which shuts down sleeping microcontrollers. Choose a version with always-on output, or add a small load.
Pass-through (charging while powering) works on the integrated 2 A boards, but the output may blink when the charger is plugged in.
18650 power bank module pinout
The pins on the 18650 power bank module and what each one does.
| Pin | Function |
|---|---|
| B+ / B- | Cell(s) |
| USB in | Charging |
| 5V OUT / USB | Output |
| Button | Wake (some) |
- B+ / B-
- Cell(s)
- USB in
- Charging
- 5V OUT / USB
- Output
- Button
- Wake (some)
Wiring the 18650 power bank module
Connect the 18650 power bank module like this.
| 18650 power bank module pin | ESP32 project | Uno project |
|---|---|---|
| B+ / B- | 2 x 18650 in parallel | 1 x 18650 |
| 5V OUT | ESP32 5V pin | Uno 5V pin |
- B+ / B-
- ESP32 project:
- 2 x 18650 in parallel
- Uno project:
- 1 x 18650
- 5V OUT
- ESP32 project:
- ESP32 5V pin
- Uno project:
- Uno 5V pin
Example code
A minimal sketch to check the part works.
1. Connect the battery first, then the input source.
2. Measure charge voltage at the battery terminals.
3. Watch cell temperature during the first full charge.Setup and tuning
charge every cell to the same voltage before joining them in parallel.
choose a version without auto-off for IoT projects that sleep at low current.
the 2 A boards can power the load while charging, but the output may blink when the charger is plugged in.
plan for about 1 A from one cell; use two or more cells in parallel for 2 A.
treat the capacity reading as an estimate.
What you need
Shop this list6 of 6 found in our store · ₹16,41,502
Power Bank Module (18650): the part this guide coversPower Bank Module (18650)₹23
5V 2A Charge-Discharge Integrated Module: another version this guide covers5V 2A Charge-Discharge Integrated Module₹77
18650 Li-ion rechargeable cell: the cell to charge or protect18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
18650 battery holder: to hold the cellBattery Holder₹45
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- TP4056 charger with MT3608 boost: two-board version.
- Battery UPS HATs: for Raspberry Pi.
- USB boost modules.
Common mistakes to avoid
- Letting auto-off cut power to a sleeping project.
- Joining a charged and an empty cell in parallel.
- Expecting 2 A from one small cell.
- Powering a Raspberry Pi 4 from it.
Frequently asked questions
Can I charge and use a power bank module at the same time?
Yes on many 2 A boards, but the output may drop for a moment when the charger is plugged in or removed.
Can it run a Raspberry Pi 4?
Not reliably: a Pi 4 needs a steady 3 A. Use a UPS HAT made for the Pi.
Why does my power bank module switch off?
Many switch off when the load is below about 50 to 100 mA. Choose an always-on version for sleeping projects.
How many 18650 cells can I connect?
Any number in parallel, as long as they are at the same voltage when joined.
Is the cell protected?
Yes. The board includes over-charge, over-discharge and short-circuit protection.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

