Component guide · Beginner · 3 min read
5V Boost Modules (USB Boost, Li-ion to 5V, SX1308, 5V to 24V USB)

Setup and Limits
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Small boost modules raise a low voltage, like one AA cell, a Li-ion cell or USB 5 V, to 5 V or higher. The USB boost and Li-ion to 5 V modules power small Arduino projects from batteries; the SX1308 is a tiny adjustable boost; the USB step-up with display gives 9, 12 or 24 V from a USB power bank for routers and LED strips.
Key specs at a glance
- Input
- 0.9 to 5 V (USB boost); 3 to 4.2 V (Li-ion); 2 to 24 V (SX1308); 5 V USB (step-up)
- Output
- 5 V USB, or adjustable up to 24 to 28 V
- Current
- About 0.5 to 1 A at 5 V; much less at higher outputs
- Efficiency
- About 85 to 93 percent
- Size
- Very small
- Note
- Output current falls as boost ratio rises
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1USB Boost Converter 0.9–5V to 5V₹38
Option 2Single-Cell Li-ion to 5V Boost Power Module₹193
Option 3SX1308 Mini Boost Converter₹35
Option 4Mini DC-DC Boost Converter Module₹48
Option 55V to 24V USB Step-Up Module with Display₹149
What the 5V USB boost module is
A USB boost module is a small step-up converter that raises a low voltage, such as one AA cell, a Li-ion cell or USB 5 V, to 5 V or more on a USB socket or pads.
Input current is higher than output current. Boosting one AA cell to 5 V at 200 mA pulls over 1 A from the cell, which drains it fast.
The USB 5 V to 12 V step-up only delivers about 0.5 A at 12 V from a 2 A USB source.
5V USB boost module pinout
The pins on the 5V USB boost module and what each one does.
| Pin | Function |
|---|---|
| IN+ / IN- or USB in | Low-voltage input |
| OUT / USB out | Output |
| Trimmer | Output (adjustable modules) |
- IN+ / IN- or USB in
- Low-voltage input
- OUT / USB out
- Output
- Trimmer
- Output (adjustable modules)
Wiring the 5V USB boost module
Set the output with a multimeter before connecting any load. Turn the trimmer slowly; many need 10 or more turns before the voltage moves.
| 5V USB boost module pin | Arduino Uno | ESP32 |
|---|---|---|
| IN+ / IN- | Supply or battery | Supply or battery |
| OUT+ / OUT- | Arduino VIN or 5V | ESP32 5V (VIN) |
| Ground | Common with the controller | Common |
- IN+ / IN-
- Arduino Uno:
- Supply or battery
- ESP32:
- Supply or battery
- OUT+ / OUT-
- Arduino Uno:
- Arduino VIN or 5V
- ESP32:
- ESP32 5V (VIN)
- Ground
- Arduino Uno:
- Common with the controller
- ESP32:
- Common
Example code
A minimal sketch to check the part works.
1. Power the module with nothing on the output.
2. Measure OUT+ to OUT- with a multimeter.
3. Turn the trimmer until the reading is correct.
4. Connect the load and measure again under load.Setup and tuning
use a protected Li-ion cell or add a low-voltage cut-off; the module keeps draining the cell.
some USB boost boards turn off below about 50 to 100 mA. Add a small dummy load or choose an always-on module for sleeping projects.
expect 0.5 to 1 A at 5 V, and much less at 12 V or 24 V.
set the SX1308 or display module with a meter before connecting the load.
use a short USB cable to avoid voltage drop at 1 A.
What you need
Shop this list9 of 10 found in our store · ₹16,41,495
USB Boost Converter 0.9–5V to 5V: the part this guide coversUSB Boost Converter 0.9–5V to 5V₹38
Single-Cell Li-ion to 5V Boost Power Module: another version this guide coversSingle-Cell Li-ion to 5V Boost Power Module₹193
SX1308 Mini Boost Converter: another version this guide coversSX1308 Mini Boost Converter₹35
Mini DC-DC Boost Converter Module: another version this guide coversMini DC-DC Boost Converter Module₹48
5V to 24V USB Step-Up Module with Display: another version this guide covers5V to 24V USB Step-Up Module with Display₹149
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
18650 Li-ion rechargeable cell: a single-cell battery input18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
18650 battery holder: to hold the cellBattery Holder₹45
TP4056 1A Li-ion charger module with protection: to charge the cellTP4056 1A Li-ion Charger Module with Protection₹19- Uno R3 development board: the controller used in the wiring tableFind this part
Alternatives and when to choose them
- MT3608 boost: common adjustable boost.
- XL6009 boost: more current.
- Power bank module: charge and boost together.
Common mistakes to avoid
- Expecting high current at 12 V from a USB port.
- Draining unprotected Li-ion cells below 3 V.
- Ignoring auto shut-off on sleeping projects.
- Connecting a load before setting adjustable modules.
Frequently asked questions
Can one AA cell run an Arduino through a boost module?
Briefly and at low current only. An AA cell cannot supply the high input current a 5 V load needs for long.
Can I power a router from a power bank?
Yes, with the 12 V USB step-up module, as long as the router needs under about 0.5 A at 12 V.
How much current does the SX1308 give?
About 1 A at low boost ratios, falling as the output voltage rises.
Why does the output keep switching off?
Some modules sleep when the load is very small. Use an always-on module or add a small load resistor.
Which boost modules are adjustable?
The SX1308 and the USB step-up with display are adjustable. The USB 5 V modules are fixed.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


