Component guide · Intermediate · 3 min read
2S to 6S Li-ion and LiFePO4 BMS Protection Boards (with Balancing)

Wiring Guide
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Multi-cell BMS boards protect series packs of 2 to 6 cells: they cut off on over-charge, over-discharge, short circuit and over-current, and balancing versions bleed extra charge from the highest cells. They are used to build 7.4, 11.1, 14.8 and 22.2 V 18650 packs for robots and tools. Choose NMC (Li-ion) or LiFePO4 versions to match your cells.
Key specs at a glance
- Cells
- 2S to 6S
- Chemistry
- Li-ion NMC (4.2 V/cell) or LiFePO4 (3.65 V/cell)
- Current
- 5 A to 40 A versions
- Balancing
- Passive, on balancing versions
- Charge voltage
- 4.2 V x cells (NMC), 3.65 V x cells (LFP)
- Port
- Common port (same P- for charge and discharge) on most
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Li-ion / LiFePO4 BMS Protection Board (2S to 6S)₹105
Option 2Li-ion Protection Board with Balancing₹65
What the 2S to 6S Li-ion BMS board is
A multi-cell BMS (battery management system) board protects a pack of 2 to 6 lithium cells in series. It disconnects the pack on over-charge, over-discharge, short circuit or over-current, and balancing versions keep the cells at equal voltage.
Connect the main B- lead first, then the balance leads in order from the lowest cell upward (B1, B2 and so on), and plug in the balance connector or B+ last. Disconnect in the reverse order. A wrong sequence can damage the protection chip.
Balancing current is small (tens of milliamps), so start with cells at the same voltage. The BMS is not a charger: use a CC/CV charger set to the pack voltage.
2S to 6S Li-ion BMS board pinout
The pins on the 2S to 6S Li-ion BMS board and what each one does.
| Pin | Function |
|---|---|
| B- | Pack negative |
| B1, B2, ... | Junctions between cells |
| B+ | Pack positive (some boards) |
| P- / C- | Load and charger negative |
- B-
- Pack negative
- B1, B2, ...
- Junctions between cells
- B+
- Pack positive (some boards)
- P- / C-
- Load and charger negative
Wiring the 2S to 6S Li-ion BMS board
Connect the 2S to 6S Li-ion BMS board like this.
| 2S to 6S Li-ion BMS board pin | 3S pack | 4S pack |
|---|---|---|
| B- | Cell 1 negative | Cell 1 negative |
| B1 | Cell 1+ / cell 2- | Cell 1+ / cell 2- |
| B2 | Cell 2+ / cell 3- | Cell 2+ / cell 3- |
| B3 / B+ | Pack + (3S) | Cell 3+ / cell 4- (4S) |
- B-
- 3S pack:
- Cell 1 negative
- 4S pack:
- Cell 1 negative
- B1
- 3S pack:
- Cell 1+ / cell 2-
- 4S pack:
- Cell 1+ / cell 2-
- B2
- 3S pack:
- Cell 2+ / cell 3-
- 4S pack:
- Cell 2+ / cell 3-
- B3 / B+
- 3S pack:
- Pack + (3S)
- 4S pack:
- Cell 3+ / cell 4- (4S)
Example code
A minimal sketch to check the part works.
1. Connect the battery first, then the input source.
2. Measure charge voltage at the battery terminals.
3. Watch cell temperature during the first full charge.Setup and tuning
connect the main B− first, then the balance leads from the lowest cell upward, and B+ or the balance plug last.
use cells of the same model and capacity, within about 0.05 V of each other before assembly.
use a CC/CV charger at 4.2 V per cell for NMC (12.6 V for 3S, 16.8 V for 4S) or 3.65 V per cell for LiFePO4 (14.6 V for 4S).
many boards need a charger connected once after assembly before the output turns on.
choose a board rated above the motor start current, not just the running current.
What you need
Shop this list7 of 7 found in our store · ₹16,43,820
Li-ion / LiFePO4 BMS Protection Board (2S to 6S): the part this guide coversLi-ion / LiFePO4 BMS Protection Board (2S to 6S)₹105
Li-ion Protection Board with Balancing: another version this guide coversLi-ion Protection Board with Balancing₹65
18650 Li-ion rechargeable cell: the cell to charge or protect18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
18650 battery holder: to hold the cellBattery Holder₹45
iMAX B6 balance charger: to balance-charge packs on the benchiMAX B6 Balance Charger₹2,339
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
SMPS power supply in metal enclosure (5/12/24 V): a 12 or 24 V charging sourceSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- Smart BMS (Daly, JBD): high current with app.
- BMS boards: concepts.
- Lithium batteries.
Common mistakes to avoid
- Connecting the balance leads in the wrong order.
- Using an NMC board with LiFePO4 cells.
- Building a pack from unmatched cells.
- Charging with a charger set for the wrong cell count.
Frequently asked questions
Does a BMS board charge the battery?
No. It protects the pack. Charge it with a CC/CV charger set to the pack's full voltage.
Why is there no output after I assembled the pack?
Many BMS boards start in protection mode. Connect the charger briefly to wake them up.
How fast does the BMS balance the cells?
Slowly, at tens of milliamps, so start with cells at the same voltage.
Will it handle motor start current?
Choose a board with plenty of margin; motor inrush can trip a board rated only for running current.
Can I use it with LiFePO4 cells?
Only with an LFP version. NMC boards over-charge LiFePO4 cells.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

