Component guide · Advanced · 3 min read
Daly, JBD and Anion BMS for 4S to 16S Li-ion and LiFePO4 Packs

Wiring and Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These BMS boards protect large battery packs from 12 V to 48 V and beyond, at 20 A to 200 A. Daly and JBD make widely used standard and smart versions; smart versions add Bluetooth, UART or CAN so you can watch cell voltages, set limits and talk to inverters. They suit e-bikes, solar storage, AGVs and power walls.
Key specs at a glance
- Series
- 4S to 16S (and more)
- Chemistry
- NMC Li-ion or LiFePO4 versions
- Current
- 20 A to 200 A continuous
- Balancing
- Passive, about 30 to 60 mA
- Smart features
- Bluetooth app, UART, RS485 or CAN
- Port
- Common or separate charge port
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Daly Smart BMS (LiFePO4, CAN)₹7,999
Option 2Daly Waterproof BMS (Standard)₹937
Option 3JBD (Jiabaida) LiFePO4 BMS₹1,050
Option 4Li-ion NMC BMS with Balancing, Common Port (7S to 16S)₹791
Option 5LiFePO4 BMS with Balancing, Common Port (4S / 8S)₹1,195
What the Smart BMS (Daly, JBD, Anion) is
Smart BMS boards from Daly and JBD protect lithium battery packs (Li-ion, LiFePO4) with cell balancing, over-charge, over-discharge and over-current protection, plus Bluetooth or UART data.
Set the chemistry correctly in the app for smart boards; LFP and NMC limits differ a lot.
Wire the balance harness to the pack before plugging it into the BMS, check each wire voltage with a meter, then plug in. Connect B- last.
Smart BMS (Daly, JBD, Anion) pinout
The pins on the Smart BMS (Daly, JBD, Anion) and what each one does.
| Pin | Function |
|---|---|
| B- | Pack negative (thick wire) |
| P- / C- | Load and charger negative |
| Balance harness | B0 to Bn |
| NTC | Temperature sensors |
| Comms | UART, RS485 or CAN |
- B-
- Pack negative (thick wire)
- P- / C-
- Load and charger negative
- Balance harness
- B0 to Bn
- NTC
- Temperature sensors
- Comms
- UART, RS485 or CAN
Wiring the Smart BMS (Daly, JBD, Anion)
Connect the Smart BMS (Daly, JBD, Anion) like this.
| Smart BMS (Daly, JBD, Anion) pin | Solar storage | E-bike / AGV |
|---|---|---|
| Balance plug | Checked in order with a meter | Same |
| B- | Pack negative | Same |
| P- | Inverter/charger negative | Motor controller negative |
- Balance plug
- Solar storage:
- Checked in order with a meter
- E-bike / AGV:
- Same
- B-
- Solar storage:
- Pack negative
- E-bike / AGV:
- Same
- P-
- Solar storage:
- Inverter/charger negative
- E-bike / AGV:
- Motor controller negative
Example code
A minimal sketch to check the part works.
Measure each pin from B0 (pack -):
B1 ~ 1 cell, B2 ~ 2 cells, ... Bn ~ full pack.
If any reading is out of order, fix it before plugging in.Setup and tuning
buy the BMS for your exact series count and chemistry; settings differ for LiFePO4 and NMC.
connect balance leads in order from B- up, with the BMS unplugged; only then plug the balance connector.
choose continuous current above your load, with a margin.
connect over Bluetooth to set voltages and watch each cell.
add a fuse on the pack output.
What you need
Shop this list8 of 8 found in our store · ₹14,737
Daly Smart BMS (LiFePO4, CAN): the part this guide coversDaly Smart BMS (LiFePO4, CAN)₹7,999
Daly Waterproof BMS (Standard): another version this guide coversDaly Waterproof BMS (Standard)₹937
JBD (Jiabaida) LiFePO4 BMS: another version this guide coversJBD (Jiabaida) LiFePO4 BMS₹1,050
Li-ion NMC BMS with Balancing, Common Port (7S to 16S): another version this guide coversLi-ion NMC BMS with Balancing, Common Port (7S to 16S)₹791
LiFePO4 BMS with Balancing, Common Port (4S / 8S): another version this guide coversLiFePO4 BMS with Balancing, Common Port (4S / 8S)₹1,195
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
iMAX B6 balance charger: to balance-charge packs on the benchiMAX B6 Balance Charger₹2,339
INA219 current and power monitor module: to log charge and load currentINA219 Current and Power Monitor Module₹249
Alternatives and when to choose them
- 2S to 6S BMS: small packs.
- BMS boards.
- Lithium batteries.
Common mistakes to avoid
- Plugging the balance lead before checking order.
- Wrong chemistry setting.
- Undersized current rating.
- No fuse.
Frequently asked questions
Why must balance leads be connected in order?
Wrong order can put high voltage across the BMS chips and destroy it.
Can I use a Li-ion BMS for LiFePO4?
No, voltages differ; buy or configure the right chemistry.
Why does the BMS cut power under load?
Over-current or low cell voltage protection has tripped; check the app for the cause.
What does balancing do?
It equalises cell voltages so the pack charges evenly.
Can I read BMS data with ESP32?
Yes, over UART or Bluetooth using open-source ESPHome or Arduino libraries.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
