Component guide · Intermediate · 5 min read
4-20 mA Pressure Transmitter (OULD, FirstRate, Ascenta)

Loop Wiring and Arduino
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A 4-20 mA pressure transmitter controls the current in a two-wire loop: 4 mA at zero pressure and 20 mA at full scale. Current does not drop along long cables, so these suit pumps, tanks and hydraulics wired back to a PLC or panel. Power the loop from 12 to 24 V, put a 250 ohm resistor or a 4-20 mA converter in it, and read 1 to 5 V on an analog pin.
Key specs at a glance
- Output
- 4 to 20 mA, two-wire loop
- Supply
- 9 to 30 V DC (24 V typical)
- Ranges
- 0 to 6 bar up to 600 bar by model
- Accuracy
- 0.25 to 0.5 percent of full scale typical
- Connections
- Hirschmann DIN plug, Packard or cable gland
- Extras
- PT-511 and ME260P have a digital display; FST800-217 adds a PT100 temperature output
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1OULD PT-506 Water Pressure Transmitter (0-1.6MPa) – 4-20mA Output₹1,549
Option 2OULD PT-301L Pressure Transmitter (0-4MPa) – 4-20mA Output, Ceramic Sensor₹1,649
Option 3OULD PT-306 Air Pressure Transmitter (0-4MPa) | 4-20mA Output | 0.5% Accuracy₹1,541
Option 4OULD PT-511 Pressure Transmitter (Digital Display) | 0-6MPa | 4-20mA Output₹3,049
Option 5FirstRate FST800-1000 Pressure Transmitter Oil Sensor, 0–25 Bar, 4–20mA Output, 9–30V DC, G1/4 Male Port₹2,189
Option 6FirstRate FST800-211A Pressure Transmitter Sensor, 0-6 bar Gauge, 4-20mA Output, 9-30VDC, G1/4 Port, 3M Cable₹5,099
What the 4-20 mA pressure transmitter is
In a two-wire transmitter the same two wires carry power and signal. The supply's positive goes to the transmitter, the transmitter's other terminal returns through the measuring resistor or PLC input, and the loop closes back at the supply's negative.
Reading below about 3.8 mA means a broken wire or failed sensor, which is the main reason industry prefers 4 to 20 mA. Ceramic sensors (OULD PT-301L, CP-100) resist corrosion; stainless diaphragms suit water and oil.
4-20 mA pressure transmitter pinout
The pins on the 4-20 mA pressure transmitter and what each one does.
| Pin | Function |
|---|---|
| + (1) | Loop supply positive (red or terminal 1) |
| - (2) | Loop output, through the load back to supply negative |
| Earth (DIN plug) | Case or shield ground |
- + (1)
- Loop supply positive (red or terminal 1)
- - (2)
- Loop output, through the load back to supply negative
- Earth (DIN plug)
- Case or shield ground
Wiring the 4-20 mA pressure transmitter
A 250 ohm resistor turns 4 to 20 mA into 1 to 5 V for a 5 V Arduino. For a 3.3 V board use about 150 ohm (0.6 to 3 V) or a 4-20 mA converter board. Keep supply negative and board ground common.
| 4-20 mA pressure transmitter pin | Arduino Uno | ESP32 |
|---|---|---|
| Transmitter + | 24 V supply + | 24 V supply + |
| Transmitter - | 250 ohm resistor to GND, junction to A0 | Converter board IN+; converter out to GPIO 34 |
| Supply - | Arduino GND | ESP32 GND |
- Transmitter +
- Arduino Uno:
- 24 V supply +
- ESP32:
- 24 V supply +
- Transmitter -
- Arduino Uno:
- 250 ohm resistor to GND, junction to A0
- ESP32:
- Converter board IN+; converter out to GPIO 34
- Supply -
- Arduino Uno:
- Arduino GND
- ESP32:
- ESP32 GND
Example code
Change RANGE_BAR for your model. Use a 0.1 percent resistor for accuracy, or an ADS1115 for 16-bit readings.
const float RANGE_BAR = 10.0;
void setup() { Serial.begin(9600); }
void loop() {
float v = analogRead(A0) * 5.0 / 1023.0;
float mA = v / 250.0 * 1000.0;
if (mA < 3.8) { Serial.println("Loop open or sensor fault"); }
else {
float bar = (mA - 4.0) / 16.0 * RANGE_BAR;
Serial.print(mA, 2); Serial.print(" mA "); Serial.print(bar, 2); Serial.println(" bar");
}
delay(500);
}Setup and tuning
with 250 ohm in the loop, use at least 15 V; 24 V gives margin for long cable.
connect straight to a PLC analog input set to 4 to 20 mA.
check 4 mA at zero with a multimeter in series, and adjust the offset in code.
the PT-511 and ME260P show pressure locally while sending the loop signal.
What you need
Shop this list19 of 20 found in our store · ₹40,255
OULD PT-506 Water Pressure Transmitter (0-1.6MPa) – 4-20mA Output: the part this guide coversOULD PT-506 Water Pressure Transmitter (0-1.6MPa) – 4-20mA Output₹1,549
OULD PT-301L Pressure Transmitter (0-4MPa) – 4-20mA Output, Ceramic Sensor: another version this guide coversOULD PT-301L Pressure Transmitter (0-4MPa) – 4-20mA Output, Ceramic Sensor₹1,649
OULD PT-306 Air Pressure Transmitter (0-4MPa) | 4-20mA Output | 0.5% Accuracy: another version this guide coversOULD PT-306 Air Pressure Transmitter (0-4MPa) | 4-20mA Output | 0.5% Accuracy₹1,541
OULD PT-511 Pressure Transmitter (Digital Display) | 0-6MPa | 4-20mA Output: another version this guide coversOULD PT-511 Pressure Transmitter (Digital Display) | 0-6MPa | 4-20mA Output₹3,049
FirstRate FST800-1000 Pressure Transmitter Oil Sensor, 0–25 Bar, 4–20mA Output, 9–30V DC, G1/4 Male Port: another version this guide coversFirstRate FST800-1000 Pressure Transmitter Oil Sensor, 0–25 Bar, 4–20mA Output, 9–30V DC, G1/4 Male Port₹2,189
FirstRate FST800-211A Pressure Transmitter Sensor, 0-6 bar Gauge, 4-20mA Output, 9-30VDC, G1/4 Port, 3M Cable: another version this guide coversFirstRate FST800-211A Pressure Transmitter Sensor, 0-6 bar Gauge, 4-20mA Output, 9-30VDC, G1/4 Port, 3M Cable₹5,099
FirstRate FST800-4001 Hydraulic Pressure Transmitter Sensor, 0~600 Bar, 4~20 mA Output, 9~30 V DC, G1/4 Male Port, M12 Connector: another version this guide coversFirstRate FST800-4001 Hydraulic Pressure Transmitter Sensor, 0~600 Bar, 4~20 mA Output, 9~30 V DC, G1/4 Male Port, M12 Connector₹6,379
Ascenta PW618 Pressure Sensor 0-10bar 4-20mA Output – Hirschman Connector, M20x1.5 Port: another version this guide coversAscenta PW618 Pressure Sensor 0-10bar 4-20mA Output – Hirschman Connector, M20x1.5 Port₹1,103
Ascenta PW618 Pressure Sensor – 0-20 bar Gauge, 4-20mA Output, Hirschman Connector, M20x1.5 Port: another version this guide coversAscenta PW618 Pressure Sensor – 0-20 bar Gauge, 4-20mA Output, Hirschman Connector, M20x1.5 Port₹1,109
OULD CP-100 Pressure Sensor Module (0-200 Bar) – 4-20mA Output, Ceramic Diaphragm: another version this guide coversOULD CP-100 Pressure Sensor Module (0-200 Bar) – 4-20mA Output, Ceramic Diaphragm₹319
OULD CP-100 Pressure Sensor Module | 0-400 Bar | 4-20mA Output | Ceramic Piezoresistive: another version this guide coversOULD CP-100 Pressure Sensor Module | 0-400 Bar | 4-20mA Output | Ceramic Piezoresistive₹319
FirstRate FST800-217 Pressure & Temperature Sensor, 0-60 bar Gauge, 4-20mA & PT100 Output, G1/4 Port, 1.5m Cable IP65: another version this guide coversFirstRate FST800-217 Pressure & Temperature Sensor, 0-60 bar Gauge, 4-20mA & PT100 Output, G1/4 Port, 1.5m Cable IP65₹8,849
ME260P 4-20mA Battery Powered Digital Pressure Gauge – IP65, 0-100MPa, NPT 1/4″: another version this guide coversME260P 4-20mA Battery Powered Digital Pressure Gauge – IP65, 0-100MPa, NPT 1/4″₹5,239- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
24V 4A switching power supply board: the loop supply for a transmitter24V 4A AC-DC Switching Power Supply Board₹411
4-20mA to 0-5V converter board: to read loop current on an analog pin4-20mA to 0-5V Converter Board₹82
DFRobot Gravity analog current to voltage converter (4-20 mA): a ready-made 4 to 20 mA receiverDFRobot Gravity Analog Current to Voltage Converter (4–20mA)₹531
ADS1115 16-bit 4-channel ADC module: for accurate readings on an ESP32 or 3.3 V boardADS1115 16-Bit 4-Channel ADC Module₹199
Resistor kit: for dividers and a 250 ohm current sense resistorResistor Assortment Kit₹250Closest match, check the specs
Alternatives and when to choose them
- 0.5-4.5 V transducers: simpler for short cables.
- 4-20 mA signal conditioners: converters and isolators for the loop.
- Submersible level transmitters: the same signal for tank levels.
Common mistakes to avoid
- Connecting the transmitter straight across 24 V without a load.
- Using a 5 V supply for the loop.
- Forgetting a common ground between supply and board.
- Choosing a range far above the system pressure.
Frequently asked questions
Why 4 mA and not 0 mA at zero?
So a broken wire (0 mA) can be told apart from zero pressure.
How long can the cable be?
Hundreds of metres with a 24 V supply.
Can an ESP32 read it?
Yes, through a converter board or a 150 ohm resistor and the ADC, or an ADS1115.
Ceramic or stainless sensor?
Ceramic for corrosive or dirty media, stainless for clean water, air and oil.
Can it go to a Modbus system?
Yes, through a Modbus analog input module.
Parts for this guide
- ₹1,549View
- ₹1,649View
- ₹1,541View
- ₹3,049View
FirstRate FST800-1000 Pressure Transmitter Oil Sensor, 0–25 Bar, 4–20mA Output, 9–30V DC, G1/4 Male Port₹2,189View
FirstRate FST800-211A Pressure Transmitter Sensor, 0-6 bar Gauge, 4-20mA Output, 9-30VDC, G1/4 Port, 3M Cable₹5,099View
FirstRate FST800-4001 Hydraulic Pressure Transmitter Sensor, 0~600 Bar, 4~20 mA Output, 9~30 V DC, G1/4 Male Port, M12 Connector₹6,379View- ₹1,103View
- ₹1,109View
- ₹319View
- ₹319View
FirstRate FST800-217 Pressure & Temperature Sensor, 0-60 bar Gauge, 4-20mA & PT100 Output, G1/4 Port, 1.5m Cable IP65₹8,849View- ₹5,239View
- ₹359View
- ₹389View
- ₹411View
- ₹82View
- ₹531View
- ₹199View
- ₹33View
- ₹177View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



